LEANDER, TX —
OSHA Inspection: HARDWOOD PRODUCTS & DOORS, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of HARDWOOD PRODUCTS & DOORS, INC. in 9430 RANCH TO MARKET ROAD 2243, LEANDER, TX 78641 (NAICS 321999). OSHA activity number 347089245.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HARDWOOD PRODUCTS & DOORS, INC.
- Site address
- 9430 RANCH TO MARKET ROAD 2243
- City
- LEANDER
- State
- TX
- ZIP
- 78641
- Mailing
- 9430 RANCH TO MARKET ROAD 2243, LEANDER, TX 78641
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321999
- Employees
- 10
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.22 B
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $2,009 · Current $1,205 Reduced
General-duty citation text
29 CFR 1910.22(b): The employer did not ensure that each walking-working surface can support the maximum intended load for that surface. On or about November 11, 2023, and at times prior thereto, materials were stored on the roof of a fabricated office inside the facility without ensuring the load could be supported, exposing employees working inside the office to the hazard of being struck-by the load or ceiling.
Recent events (2)
- — I (S) $1205.4
- — Z (S) $2009
1910.178 L04 III
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $2,009 · Current $1,205 Reduced
General-duty citation text
29 CFR 1910.178(l)(4)(iii): An evaluation of each powered industrial truck operator's performance was not being conducted at least once every three years. On or about November 11, 2023, and at times prior thereto, forklift operators' performance had not been evaluated for over 15 years, exposing both the operators and those nearby to the hazard of being struck-by the forklift or load.
Recent events (2)
- — I (S) $1205.4
- — Z (S) $2009
1910.213 C01
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $2,679 · Current $1,607 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut. On or about November 11, 2023, and at times prior thereto, a Grizzly G1023ZX 10" Table Saw used for making rip cuts was unguarded, exposing employees to the hazard of being struck-by the rotating blade.
Recent events (2)
- — I (S) $1607.4
- — Z (S) $2679
1910.213 C02
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator. On or about November 11, 2023, and at times prior thereto, a Grizzly G1023ZX 10" Table Saw used for making rip cuts was not furnished with a spreader, exposing employees to the hazard of being struck-by the material being thrown back.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 C03
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: On or about November 11, 2023, and at times prior thereto, a Grizzly G1023ZX 10" Table Saw used for making rip cuts was not equipped with non-kickback fingers or dogs, exposing employees to the hazard of being struck-by the kick backed materials.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.215 A02
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $2,009 · Current $1,205 Reduced
General-duty citation text
29 CFR 1910.215(a)(2): Abrasive wheel(s) used on grinding machinery were not provided with safety guard(s) which covered the spindle end, nut, flange projections. On or about November 11, 2023, and at times prior thereto, an abrasive wheel used for shaping jointing stones was unguarded, exposing employees to the hazard of being struck-by the spinning wheel.
Recent events (2)
- — I (S) $1205.4
- — Z (S) $2009
1910.215 A04
- Issued
- Dec 18, 2023
- Abate by
- Jan 16, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work. On or about November 11, 2023, and at times prior thereto, an abrasive wheel used for shaping jointing stones was not equipped with a work rest, exposing employees to the hazard of being struck-by the spinning wheel.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Hardwood Products & Doors, INC.
View Hardwood Products & Doors, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 321999)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347089245.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.