TONAWANDA, NY —
OSHA Inspection: HEBELER, LLC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of HEBELER, LLC in 2000 MILITARY ROAD, TONAWANDA, NY 14150 (NAICS 333999). OSHA activity number 347847584.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- HEBELER, LLC
- Site address
- 2000 MILITARY ROAD
- City
- TONAWANDA
- State
- NY
- ZIP
- 14150
- Mailing
- 2000 MILITARY ROAD, TONAWANDA, NY 14150
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333999
- Employees
- 70
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C04 I
- Issued
- Nov 21, 2024
- Abate by
- Dec 16, 2024
- Penalty
- Initial $6,857 · Current $4,120 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not documented or utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) On or about 10/29/2024, in the Layout Area, energy control procedures (Lockout/Tagout LOTO) were not documented or utilized when employees performed servicing and/or maintenance activities on the Big and Small press brakes such as, but not limited to setting up dies on the press brake. Employees were exposed to amputation hazards. b) On or about 10/29/2024 in the Layout Area, energy control procedures (Lockout/Tagout LOTO) were not documented or utilized when employees performed servicing and/or maintenance activities on vertical and horizontal saws such as, but not limited to changing the blade. Employees were exposed to amputation hazards. ABATEMENT CERTIFICATION REQUIRED
Recent events (2)
- — I (S) $4120
- — Z (S) $6857
1910.147 C07 I
- Issued
- Nov 21, 2024
- Abate by
- Dec 16, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: a) On or about 10/24/2024 throughout the establishment; where employees perform servicing and/or maintenance activities such as, but not limited to: changing blades on saws and setting up dies on presses, employees were not trained to recognize hazardous energy sources in the workplace and the means and methods (procedures) used to control those hazardous energy sources during servicing and/or maintenance of the machines and equipment in the workplace. Employees were exposed to amputation hazards. ABATEMENT CERTIFICATION REQUIRED
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C06 I
- Issued
- Nov 21, 2024
- Abate by
- Dec 16, 2024
- Penalty
- Initial $6,857 · Current $4,115 Reduced
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed: a) On or about 10/29/2024, throughout the establishment, the employer did not conduct periodic inspections of the Lockout/Tagout procedures for employees that perform servicing activities such as, but not limited to changing blades on saws, setting dies on press brakes, or servicing the big roller. ABATEMENT CERTIFICATION REQUIRED
Recent events (2)
- — I (S) $4115
- — Z (S) $6857
1910.212 A01
- Issued
- Nov 21, 2024
- Abate by
- Dec 16, 2024
- Penalty
- Initial $6,857 · Current $4,115 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding were not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a) On or about, 10/29/2024, in the Layout Area, employees were exposed to rotating parts hazards when operating the Clausing- Colchester 17" Lathe without guarding the chuck. b) On or about 10/29/2024, in the Layout Area, employees were exposed to amputation hazards when operating the Press Brakes without point-of-operation guarding. ABATEMENT DOCUMENTATION REQUIRED
Recent events (2)
- — I (S) $4115
- — Z (S) $6857
More inspections in this industry (NAICS 333999)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347847584.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.