ORCHARD PARK, NY —
OSHA Inspection: ADVAN-TECH MANUFACTURING INC
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of ADVAN-TECH MANUFACTURING INC in 3645 CALIFORNIA ROAD, ORCHARD PARK, NY 14127 (NAICS 332710). OSHA activity number 347922130.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ADVAN-TECH MANUFACTURING INC
- Site address
- 3645 CALIFORNIA ROAD
- City
- ORCHARD PARK
- State
- NY
- ZIP
- 14127
- Mailing
- 3645 CALIFORNIA ROAD, ORCHARD PARK, NY 14127
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332710
- Employees
- 18
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C01
- Issued
- Jan 13, 2025
- Abate by
- Feb 5, 2025
- Penalty
- Initial $3,918 · Current $1,959 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: a) On or about 12/09/2024 throughout the establishment; where employees perform servicing and/or maintenance activities such as, but not limited to: changing blades on saws. The employer has not developed machine specific energy control procedures, nor has the employer trained or periodically reviewed employees performing covered operations where the employees were exposed to potentially hazardous energy sources and amputation hazards. ABATEMENT DOCUMENTATION REQUIRED
Recent events (3)
- — F (S) $1959
- — C (S) $3918
- — Z (S) $3918
1910.147 C04 I
- Issued
- Jan 13, 2025
- Abate by
- Feb 5, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a) On or about 12/09/2024 throughout the establishment; employees perform servicing and/or maintenance activities such as, but not limited to: changing blades on saws without utilizing Lockout /Tagout (LOTO) procedures. Employees were exposed to amputation hazards. ABATEMENT CERTIFICATION REQUIRED
Recent events (3)
- — F (S) $0
- — C (S) $0
- — Z (S) $0
1910.147 C07 I
- Issued
- Jan 13, 2025
- Abate by
- Feb 5, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i): The employer did not provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees: a) On or about 12/09/2024 throughout the establishment; where employees perform servicing and/or maintenance activities such as, but not limited to: changing blades on saws, employees were not trained to recognize hazardous energy sources in the workplace and the means and methods (procedures) used to control those hazardous energy sources during servicing and/or maintenance of the machines and equipment in the workplace. Employees were exposed to amputation hazards. ABATEMENT CERTIFICATION REQUIRED
Recent events (3)
- — F (S) $0
- — C (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- Jan 13, 2025
- Abate by
- Feb 5, 2025
- Penalty
- Initial $3,134 · Current $1,567 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding were not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a) On or about, 12/09/2024, in the Machinery Area, employees were exposed to rotating parts hazards when operating the LYNX-2100LSY Doosan CNC without guarding the opening on the side of the machine. ABATEMENT CERTIFICATION REQUIRED
Recent events (3)
- — F (S) $1567
- — C (S) $3134
- — Z (S) $3134
More inspections at Advan-Tech Manufacturing INC
View Advan-Tech Manufacturing INC's full OSHA safety record →
More inspections in this industry (NAICS 332710)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347922130.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.