LINCOLNWOOD, IL —
OSHA Inspection: M3 EXTERIORS LLC
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of M3 EXTERIORS LLC in 3811 W PRATT AVE, LINCOLNWOOD, IL 60712 (NAICS 238140). OSHA activity number 347951121.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- M3 EXTERIORS LLC
- Site address
- 3811 W PRATT AVE
- City
- LINCOLNWOOD
- State
- IL
- ZIP
- 60712
- Mailing
- 2848 S KOSTNER AVE., CHICAGO, IL 60623
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238140
- Employees
- 4
- Ownership type
- A
Citations
4 citations on file for this inspection.
1926.451 B05 II
- Issued
- May 13, 2025
- Abate by
- Jun 9, 2025
- Penalty
- Initial $4,965 · Current $2,400 Reduced
General-duty citation text
29 CFR 1926.451(b)(5)(ii): Each platform greater than 10 feet in length shall not extend over its support more than 18 inches (46 cm), unless it is designed and installed so that the cantilevered portion of the platform is able to support employees without tipping, or has guardrails which block employee access to the cantilevered end. a) On or about December 24, 2024, employees were working on a scaffold platform which extended over its support by approximately 25 inches and was not blocked with guardrails. In accordance with 29 CFR 1903.19(d), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET), and in addition, documentation demonstrating that abatement is complete must be included with your certification. This documentation may include, but is not limited to, evidence of the purchase or repair of the equipment, photographic or video evidence of abatement, or other written records.
Recent events (2)
- — I (S) $2400
- — Z (S) $4965
1926.451 B07
- Issued
- May 13, 2025
- Abate by
- Jun 9, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.451(b)(7):On scaffolds where platforms are overlapped to create a long platform, the overlap shall occur only over supports, and shall not be less than 12 inches (30 cm) unless the platforms are nailed together or otherwise restrained to prevent movement. a) On or about December 24, 2024, employees working from frame scaffolding were exposed to fall hazards of up to approximately 8.9 feet from an overlapped platform. In accordance with 29 CFR 1903.19(d), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET), and in addition, documentation demonstrating that abatement is complete must be included with your certification. This documentation may include, but is not limited to, evidence of the purchase or repair of the equipment, photographic or video evidence of abatement, or other written records.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1926.451 G01
- Issued
- May 13, 2025
- Abate by
- Jun 9, 2025
- Penalty
- Initial $4,965 · Current $2,400 Reduced
General-duty citation text
29 CFR 1926.451(g)(1): Each employee on a scaffold more than 10 feet above a lower level was not protected from falling to that lower level: a) On or about December 24, 2024, employees working from a tubular frame scaffold were exposed to a fall hazard of approximately 10.8 feet. In accordance with 29 CFR 1903.19(d), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET), and in addition, documentation demonstrating that abatement is complete must be included with your certification. This documentation may include, but is not limited to, evidence of the purchase or repair of the equipment, photographic or video evidence of abatement, or other written records.
Recent events (2)
- — I (S) $2400
- — Z (S) $4965
1926.1053 B05 I
- Issued
- May 13, 2025
- Abate by
- Jun 9, 2025
- Penalty
- Initial $3,547 · Current $1,700 Reduced
General-duty citation text
29 CFR 1926.1053(b)(5)(i): Non-self-supporting ladders were not used at an angle such than the horizontal distance from the top support to the foot of the ladder way approximately one-quarter of the working length of the ladder (the distance along the ladder between the foot and the top support): a) On or about December 24, 2024, extension ladders being used were not set up at a 4:1 angle. In accordance with 29 CFR 1903.19(c), abatement certification is required for this violation (using the CERTIFICATION OF CORRECTIVE ACTION WORKSHEET).
Recent events (2)
- — I (S) $1700
- — Z (S) $3547
More inspections in this industry (NAICS 238140)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347951121.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.