RUMFORD, RI —
OSHA Inspection: J & M DIAMOND TOOL, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of J & M DIAMOND TOOL, INC. in 43 ROGER WILLIAMS AVENUE, RUMFORD, RI 02916 (NAICS 333515). OSHA activity number 348002502.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- J & M DIAMOND TOOL, INC.
- Site address
- 43 ROGER WILLIAMS AVENUE
- City
- RUMFORD
- State
- RI
- ZIP
- 02916
- Mailing
- 43 ROGER WILLIAMS AVENUE, RUMFORD, RI 02916
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333515
- Employees
- 24
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.215 A04
- Issued
- May 9, 2025
- Penalty
- Initial $2,837 · Current $1,986 Reduced
General-duty citation text
29 CFR 1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work. (a) Worksite - Production Area: On or about 1/28/2025, employees were exposed to caught-in hazards while utilizing a Baldo grinder CAT NO. 612E Serial Number W896 without tool work-rests.
Recent events (2)
- — I (S) $1985.9
- — Z (S) $2837
1910.219 C02 I
- Issued
- May 9, 2025
- Abate by
- Jun 26, 2025
- Penalty
- Initial $2,837 · Current $1,986 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting. (a) Worksite - Lapping Room: On or about 1/28/2025, employees were exposed to caught-in and struck-by type hazards while utilizing a lapping machine with an unguarded horizontal shaft, located less than 7-feet from the floor.
Recent events (2)
- — I (S) $1985.9
- — Z (S) $2837
1910.219 C04 I
- Issued
- May 9, 2025
- Abate by
- Jun 26, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(c)(4)(i): Unguarded projecting shaft end(s) did not present a smooth edge and end, and projected more than one half the diameter of the shaft. (a) Worksite - Lapping Room: On or about 1/28/2025, employees were exposed to the rotating ends of a lapping machine's horizontal shaft, which projected more than one half the diameter of the shaft.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E02 I
- Issued
- May 9, 2025
- Abate by
- Jun 26, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(2)(i): Overhead horizontal belt(s) with lower parts seven -7 feet or less from the floor(s) or platform(s) were not guarded on the sides and bottom in accordance with the requirements specified at CFR 1910.219(o)(3). (a) Worksite - Lapping Room: On or about 1/28/2025, employees were exposed to caught-in hazards while operating a lapping machine with an unguarded horizontal belt that was lower than 7-feet from the floor.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.132 D01
- Issued
- May 9, 2025
- Abate by
- Jun 26, 2025
- Penalty
- Initial $531 · Current $372 Reduced
General-duty citation text
29 CFR 1910.132(d)(1): The employer did not assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment (PPE). (a)Worksite: On or about 1/28/2025, the employer did not conduct and document a workplace hazard assessment for personal protective equipment (PPE), to ensure that appropriate levels of PPE are used at all times.
Recent events (2)
- — I (O) $371.7
- — Z (O) $531
More inspections at J & M Diamond Tool, INC.
View J & M Diamond Tool, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333515)
More inspections in RI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348002502.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.