LITTLETON, CO —
OSHA Inspection: LOCKHEED MARTIN
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of LOCKHEED MARTIN in 12257 S WADSWORTH, LITTLETON, CO 80125 (NAICS 336414). OSHA activity number 348093832.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LOCKHEED MARTIN
- Site address
- 12257 S WADSWORTH
- City
- LITTLETON
- State
- CO
- ZIP
- 80125
- Mailing
- ATTN: MATT HIBBS (EHS) MAIL DROP ENG 9080, DENVER, CO 80201
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336414
- Employees
- 2000
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.147 F02 II
- Issued
- Jul 30, 2025
- Abate by
- Aug 27, 2025
- Penalty
- Initial $16,550 · Current $16,550
General-duty citation text
1910.147(f)(2)(ii): The onsite employer did not ensure that his or her personnel understood and complied with restrictions and prohibitions of the outside employer's energy control procedures: (a) On or about March 4, 2025, and at times prior, the employer did not ensure that his or her personnel understood and complied with restrictions and prohibitions of the outside vendor's energy control procedures when the 2019 Powder Recovery System (PRS) machine (s/n 604342) in the Additive Manufacturing Lab (AML) would jam. An employee suffered three fingertip amputations on the right hand when reaching into the hopper system where the rotary flap resides to attempt to remove a possible jam while the machine was still in the "on" position. There was a moving rotary that caused the amputation and there was not a specific procedure for the PRS machine regarding the control of hazardous energy.
Recent events (2)
- — I (O) $16550
- — Z (S) $16550
1910.147 C07 I
- Issued
- Jul 30, 2025
- Abate by
- Aug 27, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i):The employer did not provide adequate training to ensure that the purpose and function of the energy control program was understood by employees: (a) On or about March 4, 2025, and at times prior, the employer did not ensure adequate training was provided regarding hazardous energy control while conducting servicing operations on machines and equipment such as, but not limited to, the 2019 Powder Recovery System (PRS) machine (s/n 604342) in the Additive Manufacturing Lab (AML). An employee suffered three fingertip amputations on the right hand when reaching into the hopper system where the rotary flap resides to attempt to remove a possible jam while the machine was still in the "on" position. There was a moving rotary that caused the amputation and the machine was found set to the "on" position after the incident occurred. This was not a routine production task and was a servicing task requiring equipment de-energizing.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 D03
- Issued
- Jul 30, 2025
- Abate by
- Aug 27, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(3):All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): (a) On or about March 4, 2025, and at times prior, the employer did not ensure energy isolating devices were utilized to isolate a machine from energy sources when conducting maintenance operations on the 2019 Powder Recovery System (PRS) machine, s/n 604342, in the Additive Manufacturing Lab (AML). An employee suffered three finger amputations on the right hand when reaching into the hopper system where the rotary flap resides to attempt to remove a possible jam while the machine was still in the "on" position. There was a moving rotary that caused the amputation and the machine was found set to the "on" position after the incident occurred and no tags or locks were administered.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Lockheed Martin
View Lockheed Martin's full OSHA safety record →
More inspections in this industry (NAICS 336414)
More inspections in CO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348093832.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.