BARNESVILLE, GA —
OSHA Inspection: LANGDALE FOREST PRODUCTS BANRNESVILLE, LLC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of LANGDALE FOREST PRODUCTS BANRNESVILLE, LLC in 752 GROVE ST., BARNESVILLE, GA 30204 (NAICS 321113). OSHA activity number 348095951.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LANGDALE FOREST PRODUCTS BANRNESVILLE, LLC
- Site address
- 752 GROVE ST.
- City
- BARNESVILLE
- State
- GA
- ZIP
- 30204
- Mailing
- 752 GROVE ST., BARNESVILLE, GA 30204
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321113
- Employees
- 155
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.212 A02
- Issued
- Jul 9, 2025
- Abate by
- Aug 6, 2025
- Penalty
- Initial $16,550 · Current $12,413 Reduced
General-duty citation text
29 CFR 1910.212(a)(2):Guard(s) on machine(s) were not affixed to the machine or secured elsewhere when attachment to the machine was not possible:(a) a) Planner Strapper Outfeed (Plainer side): On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the Bundle table belt and pulley were not secured in a manner that would prevent removal, exposing employees to caught-in/ pinch points while the employees are operating the machine.
Recent events (2)
- — I (S) $12412.5
- — Z (S) $16550
1910.219 D01
- Issued
- Jul 9, 2025
- Abate by
- Aug 6, 2025
- Penalty
- Initial $16,550 · Current $12,413 Reduced
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) Gang Centering table On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the Gang centering table belt and pulley were not installed to prevent exposing employees to caught-in/ pinch points while the employees are operating the machine. b) #2 Saw Edger On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the #2 Saw Edger belt and pulley were not installed to prevent exposing employees to caught-in/ pinch points while the employees are operating the machine.
Recent events (2)
- — I (S) $12412.5
- — Z (S) $16550
1910.219 F03
- Issued
- Jul 9, 2025
- Abate by
- Aug 6, 2025
- Penalty
- Initial $16,550 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven (7) feet or less above floors or platforms were not enclosed: a) Sharp Chain outfeed (Plainer side); On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the Sharp Chain outfeed motor were not installed, exposing employees to caught-in/ pinch points while the employees are operating the machine. b) Gang centering table; On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the Gang center table motor were not installed, exposing employees to caught-in/ pinch points while the employees are operating the machine. c) Fletch belt drive motor; On or about , March 10, 2025, and at times prior, the employer exposed employees to caught-in hazards, in that the machine guarding for the Fletch belt were not installed, exposing employees to caught-in/ pinch points while the employees are operating the machine.
Recent events (2)
- — I (S) $0
- — Z (S) $16550
1910.178 A06
- Issued
- Jul 9, 2025
- Abate by
- Aug 6, 2025
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(a)(6):The employer did not ensure that all nameplates or markings were maintained in a legible condition: a) Taylor GT155 10K forklift, March 10, 2025, and at times prior, the employer exposed employees to struck-by/crush-by hazards, in that the employer did not ensure that the name plate for the Taylor GT155 diesel forklift were maintained in a manner that provided safe operating parameters for employees who operated the forklift.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections in this industry (NAICS 321113)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348095951.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.