BILLINGS, MT —
OSHA Inspection: MONTANA CUSTOM MILLWORK CO.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MONTANA CUSTOM MILLWORK CO. in 9660 SOUTH FRONTAGE ROAD, BILLINGS, MT 59101 (NAICS 333243). OSHA activity number 348235300.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MONTANA CUSTOM MILLWORK CO.
- Site address
- 9660 SOUTH FRONTAGE ROAD
- City
- BILLINGS
- State
- MT
- ZIP
- 59101
- Mailing
- 9660 SOUTH FRONTAGE ROAD, BILLINGS, MT 59101
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333243
- Employees
- 9
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 C04 I
- Issued
- Aug 26, 2025
- Abate by
- Sep 15, 2025
- Penalty
- Initial $2,128 · Current $1,064 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: a. Sawmill: On or about May 8, 2025, and at times prior, employees were exposed to the caught in hazards and amputations from the release of hazardous stored energy including , but not limited to, electric, hydraulic, mechanical energy from equipment including, but not limited to; Woodmizer LT 70, Woodmizer LT 40, Morgan saw. Employees were required to perform maintenance activities without machine specific energy control procedures that clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy.
Recent events (2)
- — I (S) $1064
- — Z (S) $2128
1910.219 C02 I
- Issued
- Aug 26, 2025
- Abate by
- Sep 22, 2025
- Penalty
- Initial $1,277 · Current $639 Reduced
General-duty citation text
29 CFR 1910.219(c)(2)(i):All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting: a) Sawmill: On or about May 8, 2025, and at times prior, employees were exposed to caught in hazards from an unguarded spinning shaft on the Morgan Saw Company Planer.
Recent events (2)
- — I (S) $638.5
- — Z (S) $1277
1910.219 D01
- Issued
- Aug 26, 2025
- Abate by
- Sep 22, 2025
- Penalty
- Initial $2,979 · Current $1,490 Reduced
General-duty citation text
29 CFR 1910.219(d)(1):Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): b) 9660 S. Frontage Rd. Billings, MT 59101: On or about May 8, 2025 and at times prior, employees were exposed to caught in hazards while operating the Morgan Saw Company Planer with and unguarded spoked pully near the start and stop buttons on the machine.
Recent events (2)
- — I (S) $1489.5
- — Z (S) $2979
1910.219 E01 I
- Issued
- Aug 26, 2025
- Abate by
- Sep 22, 2025
- Penalty
- Initial $2,979 · Current $0 Reduced
General-duty citation text
29 CFR 1910.219(e)(1)(i):Horizontal belts which had both runs 42 inches or less from the floor level were not fully enclosed by guards conforming to requirements specified in 29 CFR 1910.219(m) and (o): a) 9660 S. Frontage Rd. Billings, MT 59101: On or about May 8, 2025 and at times prior, employees were exposed to caught in hazards while operating the Wood-Mizer LT 40 Hydraulic Sawmill with an unguarded belt near the base of the machine.
Recent events (2)
- — I (S) $0
- — Z (S) $2979
1910.303 G02 I
- Issued
- Aug 26, 2025
- Abate by
- Sep 22, 2025
- Penalty
- Initial $1,702 · Current $851 Reduced
General-duty citation text
29 CFR 1910.303(g)(2)(i):Except as elsewhere required or permitted by Subpart S of Part 1910, live parts of electric equipment operating at 50 volts or more were not guarded against accidental contact by use of approved cabinets or other forms of approved enclosures or by any of the means identified in paragraphs (A), (B), (C), and (D) of 29 CFR 1910.303(g)(2)(i): a) 9660 S. Frontage Rd. Billings, MT 59101: On or about May 8, 2025, and at times prior, employees were exposed to shock hazards while walking and working around exposed wiring in an open junction box powering the motor of a dust collection system.
Recent events (2)
- — I (S) $851
- — Z (S) $1702
More inspections at Montana Custom Millwork CO.
View Montana Custom Millwork CO.'s full OSHA safety record →
More inspections in this industry (NAICS 333243)
More inspections in MT
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348235300.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.