CHANNELVIEW, TX ·
OSHA Inspection: TAPCOENPRO, LLC
Fatality or catastrophe inspection · Safety discipline
At a glance
On , OSHA opened a fatality or catastrophe safety inspection of TAPCOENPRO, LLC in 16315 MARKET STREET, CHANNELVIEW, TX 77530 (NAICS 213112). OSHA activity number 348435553.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TAPCOENPRO, LLC
- Site address
- 16315 MARKET STREET
- City
- CHANNELVIEW
- State
- TX
- ZIP
- 77530
- Mailing
- 16315 MARKET STREET, CHANNELVIEW, TX 77530
What kind of inspection was it?
- Inspection type
- Fatality or catastrophe (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Last modified
- Data loaded
Establishment context
- NAICS code
- 213112
- Employees
- 130
- Ownership type
- Private (A)
Citations
6 citations on file for this inspection.
1910.147 C04 I
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $14,895 · Current $14,895
General-duty citation text
29 CFR 1910.147(c)(4)(i):Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: On�or about�August 12, 2025, an employee was changing the dies on a press brake without utilizing energy control procedures.
Recent events (2)
- · C (S) $14895
- · Z (S) $14895
1910.147 C07 I A
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Authorized employee(s) did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control: On�or about�August 12, 2025, an employee was changing the dies on a press brake without being adequately trained on the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control.
Recent events (2)
- · C (S) $0
- · Z (S) $0
1910.147 D03
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $14,895 · Current $14,895
General-duty citation text
29 CFR 1910.147(d)(3):All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): On�or about�August 12, 2025, an employee was changing the dies on a press brake without isolating the machine from its energy sources.
Recent events (2)
- · C (S) $14895
- · Z (S) $14895
1910.147 D04 I
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i):Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: On�or about�August 12, 2025, an employee was changing the dies on a press brake without placing a lock or tagout device on the energy isolating device.
Recent events (2)
- · C (S) $0
- · Z (S) $0
1910.179 B06 I
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $14,895 · Current $14,895
General-duty citation text
29 CFR 1910.179(b)(6)(i): A minimum clearance of 3 inches overhead and 2 inches laterally was not provided and maintained between crane(s) and obstructions: On�or about�August 12, 2025, employees used a crane to remove a die from a press brake and minimal clearance wasn't obtained between crane and obstructions.
Recent events (2)
- · C (S) $14895
- · Z (S) $14895
1910.179 N03 I
- Issued
- Feb 9, 2026
- Abate by
- Mar 6, 2026
- Penalty
- Initial $14,895 · Current $14,895
General-duty citation text
29 CFR 1910.179(n)(3)(i):The load was not well secured and properly balanced in the sling or lifting device before it was lifted more than a few inches: On�or about�August 12, 2025, employees did not ensure a press brake die was secured and properly balanced in the sling before it was lifted.
Recent events (2)
- · C (S) $14895
- · Z (S) $14895
More inspections at Tapcoenpro, LLC
View Tapcoenpro, LLC's full OSHA safety record →
More inspections in this industry (NAICS 213112)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 348435553.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.