NASHOTAH, WI —
OSHA Inspection: TECHNIPLAS US, LLC
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of TECHNIPLAS US, LLC in N44 W33341 WATERTOWN PLANK ROAD, NASHOTAH, WI 53058 (NAICS 326199). OSHA activity number 348503392.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TECHNIPLAS US, LLC
- Site address
- N44 W33341 WATERTOWN PLANK ROAD
- City
- NASHOTAH
- State
- WI
- ZIP
- 53058
- Mailing
- N44 W33341 WATERTOWN PLANK ROAD, NASHOTAH, WI 53058
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326199
- Employees
- 132
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 C04 I
- Issued
- Dec 19, 2025
- Abate by
- May 20, 2026
- Penalty
- Initial $8,513 · Current $4,256 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section. (a) On or about September 15, 2025, employees working on and around the L&J power press (Model #150PBPP) removing dies were exposed to crushing and amputation hazards, in-that the employer did not develop procedures for the safe removal of dies.
Recent events (3)
- — P (S) $4256
- — I (S) $4256
- — Z (S) $8513
1910.147 C06 I
- Issued
- Dec 19, 2025
- Abate by
- May 20, 2026
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed. (a) On or about September 15, 2025, the employer did not ensure that periodic inspections including a review between the inspector and each authorized employee, of the employee's responsibilities under the energy control procedure being inspected were conducted.
Recent events (3)
- — P (S) $0
- — I (S) $0
- — Z (S) $0
1910.147 C07 I
- Issued
- Dec 19, 2025
- Abate by
- May 20, 2026
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i): The employer did not provide adequate training to ensure that the purpose and function of the energy control program was understood by employees. (a) On or about September 15, 2025, an employee who conducts die changes on the L&J power press (Model #150PBPP), was not provided with training on the hazardous energy control program and procedure to control hazardous energy sources.
Recent events (3)
- — P (S) $0
- — I (S) $0
- — Z (S) $0
1910.217 C02 I A
- Issued
- Dec 19, 2025
- Penalty
- Initial $7,236 · Current $3,618 Reduced
General-duty citation text
29 CFR 1910.217(c)(2)(i)(a): Point of operation guard(s) on mechanical power press(es) did not prevent entry of hands or fingers into the point of operation by reaching through, over, under or around the guard(s). (a) On or about September 15, 2025, the employer did not ensure that a L&J power press (Model #150PBPP) was adequately guarded. The guard did not prevent employees from reaching through to the point of operation via the approximately six-inch gap on the right side of the existing guard. This exposed employee(s) to both crushing and amputation hazards.
Recent events (2)
- — I (S) $3618
- — Z (S) $7236
1904.33 A
- Issued
- Dec 19, 2025
- Abate by
- May 20, 2026
- Penalty
- Initial $1,702 · Current $851 Reduced
General-duty citation text
29 CFR 1904.33(a): The employer did not maintain the OSHA 300 log, the privacy case list, the annual summary and the OSHA 301 Incident Report forms for five (5) years following the end of the calendar year that those records covered. (a) On or before September 15, 2025, the employer did not retain the 2022 OSHA 300 Injury & Illness Log with the recordable injuries for the year as well as the 2023 OSHA 300A Summary of work-Related Injuries and Illnesses.
Recent events (3)
- — P (O) $851
- — I (O) $851
- — Z (O) $1702
More inspections at Techniplas US, LLC
View Techniplas US, LLC's full OSHA safety record →
More inspections in this industry (NAICS 326199)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 348503392.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.