OSHA Inspection: WYMAN GORDON CO

Issued

Nov 19, 1991

Abate by

Feb 24, 1992

Penalty

Initial $2,975 · Current $1,995 Reduced

General-duty citation text

SECTION 5(A)(1) OF THE OCCUPATIONAL SAFETY AND HEALTH ACT OF 1970:  THE
EMPLOYER DID NOT FURNISH EMPLOYMENT AND A PLACE OF EMPLOYMENT WHICH WERE
FREE FROM RECOGNIZED HAZARDS THAT WERE CAUSING OR LIKELY TO CAUSE DEATH OR
SERIOUS PHYSICAL HARM TO EMPLOYEES IN THAT EMPLOYEES WERE EXPOSED TO:
A)  BEING STRUCK AND/OR CRUSHED BY FORGINGS, HOIST AND ASSOCIATED PARTS
WHILE WORKING IN THE FORGE SHOP AT PRE-HEAT OVEN #2018, IN CLOSE PROXIMITY
OF P&H HOIST #3556 AND IT'S SUSPENDED LOAD.  THE HOIST HAD AN INOPERATIVE
UPPER LIMIT SWITCH, LEAKING  GEAR BOX, AND WIRE ROPE TWISTED/OR CROSSED ON
WIRE ROPE DRUM, WHICH ARE NOT IN ACCORDANCE WITH ANSI B30.16-73.  AMONG
OTHER METHODS, ONE FEASIBLE AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THES E
HAZARDS IS TO PROVIDE A PROPERLY OPERATING HOIST AND/OR REPAIR EXISTING
HOIST IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS.  AND PERFORM
FREQUENT (DAILY TO MONTHLY) AND PERIODIC (MONTHLY TO ANNUAL) INSPECTIONS OF
THE HOISTING EQUIPMENT TO DETERMINE UNSAFE CONDITIONS  SUCH AS, BUT NOT
LIMITED TO, UNSAFE CONDITIONS NOTED ABOVE.  ALL DEFICIENCIES NOTED MUST BE
RECORDED AND CORRECTIVE ACTION TAKEN.
B)  BEING STRUCK AND/OR CRUSHED BY FORGINGS, HOIST AND ASSOCIATED PARTS
WHILE WORKING IN THE HOT INSPECTION, FORGE SHOP, BUILDING #6, IN CLOSE
PROXIMITY OF P&H HOIST #5823 AND IT'S SUSPENDED LOAD.  THE HOIST HAD A
IMPROPERLY OPERATING UPPER LIMIT SWITCH, AND GEAR BOX LEAKED OIL, WHICH ARE
NOT IN ACCORDANCE WITH ANSI B30.16-1973.  AMONG OTHER METHODS, ONE FEASIBLE
AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THESE HAZARDS IS TO PROVIDE A
PROPERLY OPERATING HOIST AND/OR REPAIR EXISTING HOIST IN ACCORDANCE WITH
MANUFACTURER'S RECOMMENDATIONS, AND PERFORM FREQUENT (DAILY TO MONTHLY) AND
PERIODIC (MONTHLY TO ANNUAL) INSPECTIONS OF THE HOISTING EQUIPMENT TO
DETERMINE UNSAFE CONDITIONS SUCH AS, BUT NOT LIMITED TO, UNSAFE CONDITIONS
NOTED ABOVE.  ALL DEFICIENCIES  NOTED MUST BE RECORDED AND CORRECTIVE ACTIO N
TAKEN.
C)  BEING STRUCK AND/OR CRUSHED BY FORGINGS, HOIST AND ASSOCIATED PARTS
WHILE WORKING IN BUILDING #6, FORGE GRIND, IN CLOSE PROXIMITY OF P&H HEVI-
LIFT HOIST #4354 AND IT'S SUSPENDED LOAD.  THE HOIST HAD A DAMAGED SHEAVE
BLOCK GUARD AND GEAR BOX LEAKED OIL, WHICH ARE NOT IN ACCORDANCE WITH ANSI
B30.16-73.  AMONG OTHER METHODS, ONE FEASIBLE AND ACCEPTABLE ABATEMENT
METHOD TO CORRECT THESE HAZARDS IS TO PROVIDE A PROPERLY OPERATING HOIST
AND/OR REPAIR EXISTING HOIST IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDA-
TIONS, AND PERFORM FREQUENT (DAILY TO MONTHLY) AND PERIODIC (MONTHLY TO
ANNUAL) INSPECTIONS OF THE HOISTING EQUIPMENT TO DETERMINE UNSAFE CONDITION S
SUCH AS, BUT NOT LIMITED TO, UNSAFE CONDITIONS NOTED ABOVE.  ALL DEFICIENC-
IES  NOTED MUST BE RECORDED AND CORRECTIVE ACTION TAKEN.
d)  BEING STRUCK AND/OR CRUSHED BY FORGINGS, HOIST AND ASSOCIATED PARTS
WHILE WORKING IN BUILDING #6, FORGE GRIND, IN CLOSE PROXIMITY OF P&H HOIST
#5801 AND IT'S SUSPENDED LOAD.  THE HOIST HAD A BIRD CAGED WIRE ROPE, WHICH
IS NOT IN ACCORDANCE WITH ANSI B30.16-1973.  AMONG OTHER METHODS, ONE
FEASIBLE AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THESE HAZARDS IS TO
PROVIDE A PROPERLY OPERATING HOIST AND/OR REPAIR EXISTING HOIST IN ACCORD-
ANCE WITH MANUFACTURER'S RECOMMENDATIONS, AND PERFORM FREQUENT (DAILY TO
MONTHLY) AND PERIODIC (MONTHLY TO ANNUAL) INSPECTIONS OF THE HOISTING
EQUIPMENT TO DETERMINE UNSAFE CONDITIONS SUCH AS, BUT NOT LIMITED TO, UNSAF E
CONDITIONS NOTED ABOVE.  ALL DEFICIENCIES  NOTED MUST BE RECORDED AND
CORRECTIVE ACTION TAKEN.
e)  BEING STRUCK AND/OR CRUSHED BY DIES, HOIST AND ASSOCIATED PARTS WHILE
WORKING IN DIE SHOP, IN CLOSE PROXIMITY OF 5 TON HOIST (CH-#3946-B) AND IT' S
SUSPENDED LOAD.  THE HOIST HAD DEFECTIVE BRAKES AND IMPROPERLY OPERATING
CONTROL MECHANISMS ( ONCE THE FUNCTION CONTROL BUTTONS WERE PUSHED THE HOIS T
HAD A LENTHY DELAY BEFORE RESPONDING TO COMMAND). AMONG OTHER METHODS, ONE
FEASIBLE AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THESE HAZARDS IS TO
PROVIDE A PROPERLY OPERATING HOIST AND/OR REPAIR EXISTING HOIST IN
ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS, AND PERFORM FREQUENT (DAILY
TO MONTHLY) AND PERIODIC (MONTHLY TO ANNUAL) INSPECTIONS OF THE HOISTING
EQUIPMENT TO DETERMINE UNSAFE CONDITIONS SUCH AS, BUT NOT LIMITED TO, UNSAF E
CONDITIONS NOTED ABOVE.  ALL DEFICIENCIES  NOTED MUST BE RECORDED AND
CORRECTIVE ACTION TAKEN.
f)   BEING STRUCK BY AN OVERHEAD  LOAD  BY USING   HOISTING  ROPE  THAT HAD
SEVERAL BROKEN STRANDS IN IT AND HAD NOT BEEN REPLACED WHEN REPLACEMENT WAS
REQUIRED.  A FEASIBLE AND USEFUL METHOD TO   CORRECT  THIS HAZARD WOULD BE
HAZARD WOULD BE TO VISUALLY INSPECT ROPES PRIOR TO EACH USE AND REPLACE
THEM WHEN NEEDED.  THE FOLLOWING ARE THE AREAS WHERE  HOISTING ROPE
WAS FOUND TO BE  IN POOR CONDITION :
1) MACHINE SHOP-MACHINE #6001 :
THE 1/4" WIRE ROPE ON HOIST WG #5512 WAS IN SERVICE AND
HAD SEVERAL BROKEN WIRES ON IT.
2) TUMBLAST DEPT:
THE 1/2" TON HOIST LOCATED AT TUMBLER #4967, HAD A WIRE ROPE
THAT HAD SEVERAL BROKEN WIRES ON IT.
g)  THE HAZARDS ASSOCIATED WITH OVERLOADING A HOISTING  MECHANISMS BY
NOT HAVING THE RATED CAPACITIES OF EACH HOIST CLEARLY MARKED ON EACH
HOIST.  THE HOISTS IN THE FOLLOWING AREAS EITHER HAD NO LEDGIBLE
MARKINGS ON THEM TO INDICATE THEIR RATED CAPACITIES OR HAD MARKINGS
THAT DID NOT COINCIDE WITH THE TRUE RATED CAPACITIES OF THE HOISTS.
1) MACHINE SHOP:
HOIST #5433, RATED AT 500 LBS, HAD A 1000 LB LABLE ON THE THE
BLOCK OF THE HOIST.
2) MACHINE SHOP:
HOIST #6002 HAD NO MARKINGS ON IT TO INDICATE ITS RATED
CAPACITY.
3) MAINTENANCE MACHINE SHOP:
HOIST # E4606 , RATED AT 500 LBS, HAD A 1000 LB LABLE ON THE
BLOCK OF THE HOIST.
4) MAINTENANCE MACHINE SHOP:
P&H HOISTS # 6123 HAD NO MARKINGS ON IT TO INDICATE ITS RATED
CAPACITY.
5) MAINTENANCE MACHINE SHOP:
HOIST # 2381 HAD NO MARKINGS ON IT TO INDICATE ITS RATED
CAPACITY.
A FEASIBLE  AND USEFUL MRTHOD TO CORRECT THIS HAZARD WOULD BE TO OBTAIN
THE RATED CAPACITIES OF EACH HOIST FROM THE MANUFACTURER AND MARK THIS
RATING ON THE HOIST SO THAT IT IS LEGIBLE FROM THE GROUND.
h)  BEING STRUCK BY AN OVERHEAD LOAD WHEN OVERHEAD HOISTS WERE USED TO
LIFT MATERIAL THAT WEIGHED   MORE  THAN  THE RATED CAPACITY OF THE
HOIST.  OVERHEAD HOISTS LOCATED AT THE OPERATORS STATIONS OF VERTICAL
TURRET LATHES, WERE USED TO LIFT PARTS THAT WEIGHED IN EXCESS OF THE
RATED LOAD OF THE HOIST.  TWO SPECIFIC INSTANCES OF OVERLOADING OCCUR-
RED ON THE FOLLOWING HOISTS:
1) HOIST # 3691 (1/4 TON)- PART #69680 (OPERATION 790) WEIGHED
741 LBS PRIOR TO MACHINING (685 LBS AFTER MACHINING) AND WAS
LIFTED BY THIS 500 LB HOIST.
2) MACHINE # 5560 (1/2 TON HOIST) - PARTS WEIGHING 1008 LBS
(PART + SLINGS AND HOOKS) WERE BEING LIFTED BY  THIS 1000
LB HOIST.
A FEASIBLE AND USEFUL METHOD TO CORRECT THIS HAZARD WOULD BE TO INSURE
THAT EACH OPERATOR KNOWS THE WEIGHT OF THE MATERIAL THAT IS BEING
HANDLED AND INSURE THAT NO MATERIAL WEIGHING IN EXCESS OF THE RATED
LOAD OF THE HOIST IS LIFTED.
i)  BEING STRUCK AND/OR CRUSHED BY FORGINGS, HOIST AND ASSOCIATED PARTS
WHILE WORKING IN THE HOT INSPECTION, FORGE SHOP, BUILDING #6, IN CLOSE
PROXIMITY OF P&H HOIST #5823 AND IT'S SUSPENDED LOAD. THE HOIST HAD AN
IMPROPERLY OPERATING UPPER LIMIT SWITCH, AND GEAR BOX LEAKED OIL, WHICH ARE
NOT IN ACCORDANCE WITH ANSI B30.16-1973.  AMONG OTHER METHODS, ONE FEASIBLE
AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THESE HAZARDS IS TO PROVIDE A
PROPERLY OPERATING HOIST AND/OR REPAIR EXISTING HOIST IN ACCORDANCE WITH
MANUFACTURER'S RECOMMENDATIONS, AND PERFORM FREQUENT (DAILY TO MONTHLY) AND
PERIODIC (MONTHLY TO ANNUAL) INSPECTIONS OF THE HOISTING EQUIPMENT TO
DETERMINE UNSAFE CONDITIONS SUCH AS, BUT NOT LIMITED TO, UNSAFE CONDITIONS
NOTED ABOVE.  ALL DEFICIENCIES  NOTED MUST BE RECORDED AND CORRECTIVE ACTIO N
TAKEN.

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,975 · Current $1,205 Reduced

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  The
employer did not furnish employment and a place of employment which were
free from recognized hazards that were causing or likely to cause death or
serious physical harm to employees in that employees were exposed to:
(a)  HAVING PARTS OF THEIR BODIES CRUSHED/BURNED, BY HAVING PARTS OF
BODY INSIDE THE DIES AND/OR ACCIDENTAL CONTACT WITH HOT DIES ON HOT TRIMMER
#2066, LOCATED IN THE FORGE SHOP.  AMONG OTHER METHODS, ONE FEASIBLE AND
ACCEPTABLE ABATEMENT METHOD TO CORRECT THIS HAZARD IS TO PROVIDE A PROPERLY
COVERED FOOT TREADLE THAT WOULD PREVENT THE ACCIDENTAL OPERATION OF THE
TRIMMER FROM FALLING OR MOVING OBJECTS, OR FROM UNINTENDED OPERATION BY
ACCIDENTAL STEPPING ONTO THE FOOT CONTROL.

Issued

Nov 19, 1991

Abate by

Feb 24, 1992

Penalty

Initial $2,125 · Current $1,125 Reduced

General-duty citation text

Section 5(a)(1) of the Occupational Safety and Health Act of 1970:  The
employer did not furnish employment and a place of employment which were
free from recognized hazards that were causing or likely to cause death or
serious physical harm to employees in that employees were exposed to the
hazards associated with working in confined spaces:
(a)  BOILER ROOM:  EMPLOYEES WITH THE JOB TITLE OF THIRD CLASS
ENGINEERS AND RESPONSIBLE FOR THE INSIDE CLEANING OF THE CHAMBERS IN FURANC E
#6 ON OR ABOUT 5-28-91 WERE EXPOSED TO THE HAZARDS OF CONFINED SPACE ENTRY.
BEFORE ENTRY THE  STEAM LINES WERE NOT LOCKED/TAGGEDOUT,  SPACE NOT CHECKED
FOR AIR CONTAMINANTS AND/OR OXYGEN DEFICIENCY, PROVISIONS NOT MADE FOR
EMERGENCY STANDBY EQUIPMENT SUCH AS BUT NOT LIMITED TO SAFETY LINE HARNESS
ARRANGEMENT AND RESPIRATORS, CONFINED SPACE ENTRY PROCEDURES NOT POSTED AND
WORKERS WERE NOT TRAINED, RELATIVE TO CONFINED SPACE ENTRY AND RESCUE.
AMONG OTHER METHODS, ONE FEASIBLE METHOD TO REDUCE THIS HAZARD IS TO
ESTABLISH AND ENFORCE ADEQUATE CONFINED SPACE ENTRY PROCEDURES SUCH AS THOS E
STIPULATED BY AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI), SAFETY REQUIRE-
MENTS FOR CONFINED SPACES, ANSI Z117.1-1989.  ELEMENTS ESSENTIAL TO AN
ACCEPTABLE CONFINED SPACE ENTRY PROCEDURE INCLUDE AT A MINIMUN:
(1)  INSTRUCTION AS TO THE NATURE OF THE HAZARDS INVOLVED AND
NECESSARY PRECAUTIONS TO BE TAKEN BY EMPLOYEES RELATIVE TO CONTINED SPACE
ENTRY.
(2)  POSTING OF WRITTEN CONFINED SPACE ENTRY PROCEDURES ADJACENT TO
PITS, TANKS, VESSELS OR OTHER CONFINED SPACE AREAS WHICH MAY BE ENTERED.
(3)  USE OF CLEANING, PURGING, AND VENTILATING PROCEDURES TO REMOVE
SLUDGE AND OTHER RESIDUE PRIOR TO CONFINED SPACE ENTRY.
(4)  IMPLEMENTATION OF ESTABLISHED LOCKOUT/TAGOUT AND ISOLATION
PROCEDURES, WHERE APPLICABLE, AND ISSUANCE OF A PROPER ENTRY PERMIT PRIOR
TO CONFINED SPACE ENTRY.
(5)  USE OF ATMOSPHERIC TESTING PROCEDURES TO DETERMINE THE PRESENCE
OF HAZARDOUS AIR CONTAMINANTS AND POTENTIAL OXYGEN DEFICIENCY PRIOR TO ENTR Y
INTO THE CONFINED SPACE.
(6)  WHERE IT HAS BEEN DETERMINED THAT THE CONFINED SPACE CONTAINS
A HAZARDOUS CONCENTRATION OF AN AIR CONTAMINANT AND/OR AN OXYGEN DEFICIENCY ,
USE OF MECHANICALLY INDUCED VENTILATION IN THE CONFINED SPACE BEFORE ENTRY
AND DURING OCCUPANCY AND/OR USE OF RESPIRATORY PROTECTIVE EQUIPMENT WHICH
PROVIDES ADEQUATE PROTECTION AGAINST THE HAZARDS ENCOUNTERED.
(7)  USE OF APPROPRIATE PROTECTIVE CLOTHING, WHERE APPLICABLE.
(8)  PROVISIONS FOR A STANDBY OBSERVER LOCATED OUTSIDE THE CONFINED
SPACE INCLUDING A MEANS OF COMMUNICATION WITH THE WORKER INSIDE THE CONFINE D
SPACE AND A MEANS OF OBTAINING IMMEDIATE HELP IN AN EMERGENCY.
(9)  PROVISIONS AND PROCEDURES FOR READILY AVAILABLE EMERGENCY
STANDBY EQUIPMENT CONSISTING OF A SAFETY LINE AND HARNESS ARRANGEMENT AND
A SELF-CONTAINED POSITIVE PRESSURE BREATHING APPARATUS CERTIFIED BY THE
NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY AND HEALTH (NIOSH) AND THE MINE
SAFETY AND HEALTH ADMINISTRATION (MSHA).
(10)  IMPLEMENTATION OF PERIODIC TRAINING SESSIONS FOR EMPLOYEES
RELATIVE TO CONFINED SPACE ENTRY, RESCUE, AND FIRST-AID PROCEDURES.

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,125

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $4,250 · Current $1,250 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $2,975 · Current $1,975 Reduced

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Mar 24, 1992

Penalty

Initial $4,250 · Current $1,250 Reduced

Issued

Nov 19, 1991

Abate by

Dec 2, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 24, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 24, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Feb 14, 1992

Penalty

Initial $2,125 · Current $1,125 Reduced

Issued

Nov 19, 1991

Abate by

Jan 24, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Mar 30, 1992

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $4,250 · Current $4,075 Reduced

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $2,975 · Current $1,975 Reduced

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Jul 1, 1992

Penalty

Initial $2,975 · Current $2,975

Issued

Nov 19, 1991

Abate by

Jul 1, 1992

Penalty

Initial $2,975 · Current $2,975

Issued

Nov 19, 1991

Abate by

Dec 2, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 24, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Jan 24, 1992

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $4,250 · Current $4,250

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $4,250 · Current $4,250

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,975 · Current $2,975

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $2,125 · Current $2,125

Issued

Nov 19, 1991

Abate by

Dec 4, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Dec 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 24, 1991

Penalty

Initial $1,700 · Current $1,700

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Penalty

Initial $1,275 · Current $1,275

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $25,000 · Current $5,000 Reduced

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Penalty

Initial $850 · Current $850

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Issued

Nov 19, 1991

Abate by

Nov 25, 1991

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Issued

Nov 19, 1991

Abate by

Dec 12, 1991

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Issued

Nov 19, 1991

Abate by

Jan 26, 1992

Issued

Nov 19, 1991

Abate by

Nov 25, 1991