CARY, NC —
OSHA Inspection: ATC, INC. DBA ATLANTIC TIRE & SERVICES
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of ATC, INC. DBA ATLANTIC TIRE & SERVICES in 1380 NW MAYNARD RD., CARY, NC 27513 (NAICS 811111). OSHA activity number 312452964.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ATC, INC. DBA ATLANTIC TIRE & SERVICES
- Site address
- 1380 NW MAYNARD RD.
- City
- CARY
- State
- NC
- ZIP
- 27513
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 811111
- SIC code (legacy)
- 7538
- Employees
- 18
- Ownership type
- A
- Industry flags
- Manufacturing safety.
Citations
10 citations on file for this inspection.
95012901
- Issued
- Oct 27, 2008
- Abate by
- Dec 15, 2008
- Penalty
- Initial $2,100 · Current $2,100
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish each of his employees conditions of employment and a place of employment free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: Crushed by collapsing lifts [ Ref ANSI/ALI ALOIM -1994.4.4.4The employer shall take appropriate steps to follow the inspection procedure of the manufacturer to include having the operator inspect features on a daily basis to include (4) The proper operation of locking devices, (6) excessive wear of components,(8) Evidence of hydraulic leaks.] a)Bay #1 - the "Rotary" lift was not receiving its daily inspection that allowed the damaged upper limit switch to remain defective. b)Bay #1,3,4,5,6,8- the "Rotary" and Magnum lifts were not receiving their daily inspection that allowed the automatic safety latches to remain out of adjustment and not deploy. c)Bay #6 - the "Magnum" lift was not receiving its daily inspection and the hydraulic cylinder was left in service with an oil leak. Abatement note: One means of abatement would be to acquire the daily and weekly inspection check sheets for the equipment through the dealer and employ and enforce a documented inspection program to ensure that defected equipment is quickly identified.
95012901
- Issued
- Oct 27, 2008
- Abate by
- Dec 15, 2008
- Penalty
- Initial $700 · Current $700
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish each of his employees conditions of employment and a place of employment free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to: Crushed by unsecured vehicles [ Ref ANSI/ALI ALOIM -1994.4.5 If there are any conditions reported as described in 4.4.4 (4-10) (6) excessive wear of components, the lift shall not be used until the appropriate repairs have been made by a qualified automotive lift personnel. In order to ensure the lift id not used until repairs are made the lift shall be locked or tagged out ] a)Bay #4,6 - the Magnum lifts were reported to management as having a worn shim that allowed the vehicles to be lifted "out of square" and the lifts were to remain in service until their replacement Abatement note: One means of abatement would be to establish a "tag system " to be applied at the power control switch and on the lift controls informing employees that the lift is "Out of Service" with only management having the authority to have the tags removed after the repairs are confirmed.
1910.212 B
- Issued
- Oct 27, 2008
- Abate by
- Oct 30, 2008
- Penalty
- Initial $300 · Current $300
1910.157 E02
- Issued
- Oct 27, 2008
- Abate by
- Oct 30, 2008
1910.303 B02
- Issued
- Oct 27, 2008
- Abate by
- Oct 30, 2008
1910.304 B04 IIC
- Issued
- Oct 27, 2008
- Abate by
- Oct 30, 2008
1910.305 G02 III
- Issued
- Oct 27, 2008
- Abate by
- Nov 4, 2008
1910.334 A02 I
- Issued
- Oct 27, 2008
- Abate by
- Oct 30, 2008
1910.1200 E01 I
- Issued
- Oct 27, 2008
- Abate by
- Dec 15, 2008
1910.1200 H01 I
- Issued
- Oct 27, 2008
- Abate by
- Dec 15, 2008
More inspections at ATC, INC. DBA Atlantic Tire & Services
View ATC, INC. DBA Atlantic Tire & Services's full OSHA safety record →
More inspections in this industry (NAICS 811111)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 312452964.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.