LINCOLN, NE — 2011-03-03 00:00:00

OSHA Inspection: ADM MILLING CO.

Referral inspection · Health discipline

At a glance

On 2011-03-03 00:00:00, OSHA opened a referral health inspection of ADM MILLING CO. in 540 SOUTH ST, LINCOLN, NE 68502 (NAICS 311211). OSHA activity number 314059460.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch ADM Milling CO. — free Get an email when a new federal OSHA severe-injury report for ADM Milling CO. is published. One employer, no account, unsubscribe in one click.

Where did this inspection happen?

Establishment: ADM MILLING CO.
Site address: 540 SOUTH ST
City: LINCOLN
State: NE
ZIP: 68502
Mailing: 540 SOUTH ST., LINCOLN, NE 68502

What kind of inspection was it?

Inspection type: Referral (C)
Scope: Partial (B)
Discipline: Health
Advance notice: No
Union status: Y

When did the case open and close?

Opened: 2011-03-03 00:00:00
Closing conference: 2011-03-16 00:00:00
Case closed: 2011-11-07 00:00:00
Last modified: 2011-11-07 00:00:00
Data loaded: 2011-11-29 01:00:50

Establishment context

NAICS code: 311211
SIC code (legacy): 2041
Employees: 97
Ownership type: A

Citations

9 citations on file for this inspection.

1910.119 E03

Serious Gravity 05 4 instances 60 exposed

Issued: Apr 18, 2011
Abate by: Sep 30, 2011
Penalty: Initial $5,000 · Current $5,000

General-duty citation text

29 CFR 1910.119(e)(3):
ADM Milling Co. - Lincoln, NE - The process hazard analysis did not
address the requirements
of 29 CFR 1910.119(e)(3)(i) through (vii).
The 2007 PHA did not address the requirements of the standard including,
but not
limited to hazards of the process (nitrogen trichloride potential),
previous
incidents and facility siting.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S) $5000.00
2011-04-18 00:00:00 — Z (S) $5000.00

1910.119 E04

Serious Gravity 05 4 instances 60 exposed

Issued: Apr 18, 2011
Abate by: May 20, 2011
Penalty: Initial $5,000 · Current $5,000

General-duty citation text

29 CFR 1910.119(e)(4):
ADM Milling Co. - Lincoln, NE - The process hazard analysis was not
performed by a team
with expertise in engineering and process operations.
The 2007 PHA was not performed by a team with expertise in engineering and
process operations. The 2007 PHA was developed and conducted by the
facility
safety and environmental coordinator.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S) $5000.00
2011-04-18 00:00:00 — Z (S) $5000.00

1910.119 J02

Serious Gravity 05 1 instance 60 exposed

Issued: Apr 18, 2011
Abate by: Sep 30, 2011
Penalty: Initial $5,000 · Current $5,000

General-duty citation text

29 CFR 1910.119(j)(2):
ADM Milling Co. - Lincoln, NE - The employer did not establish and
implement written
procedures to maintain the on-going mechanical integrity of process
equipment.
Written procedures to maintain all components of the chlorine process
equipment
were incomplete and/or not included in the facility mechanical integrity
program.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.ion

Recent events (2)

2011-05-12 00:00:00 — I (S) $5000.00
2011-04-18 00:00:00 — Z (S) $5000.00

1910.119 J04 IV

Deleted Serious Gravity 05 1 instance 60 exposed

Issued: Apr 18, 2011
Abate by: Jun 20, 2011

General-duty citation text

29 CFR 1910.119(j)(4)(iv):
ADM Milling Co. - Lincoln, NE - The employer did not document each
inspection and test that
had been performed on process equipment to maintain its mechanical
integrity.
Inspections, tests or repairs on chlorine process equipment including
piping,
hoses, agitators and associated components had not been properly
documented.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S)
2011-04-18 00:00:00 — Z (S)

1910.119 O04

Serious Gravity 05 10 instances 60 exposed

Issued: Apr 18, 2011
Abate by: Sep 30, 2011
Penalty: Initial $5,000 · Current $5,000

General-duty citation text

29 CFR 1910.119(o)(4):
ADM Milling Co. - Lincoln, NE - The employer did not determine and
document an appropriate
response to each of the findings of the compliance audit required by 29
CFR 1910.119(o)(1),
and document that the deficiencies had been corrected.
Multiple findings on the facility 2010 Process Safety Compliance Audit
were
not
corrected and/or documented as corrected including, but not limited to P&ID
update (abated), PHA inadequacies, incident/near miss documentation and
mechanical integrity procedures.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S) $5000.00
2011-04-18 00:00:00 — Z (S) $5000.00

1910.120 Q06

Deleted Serious Gravity 10 2 instances 2 exposed

Issued: Apr 18, 2011
Abate by: May 20, 2011
Penalty: Initial $7,000 · Current $7,000

General-duty citation text

29 CFR 1910.120(q)(6):
ADM Milling Co. - Lincoln, NE - Employee(s) who participated, or were
expected to
participate, in emergency response, were not given training in accordance
with 29 CFR
1910.120(q)(6)(iii)[A] through [I].
Employee(s) engaged in an emergency response operation, stopping a
chlorine gas
leak, were not trained/certified to the hazardous materials technician
level.
Abatement certification and abatement documentation is required for this
violation. The
documentation should include written verification of abatement, applicable
measurements or
monitoring results, and photographs or videos which you believe will be
helpful. The abatement
certification sheet is enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S) $7000.00
2011-04-18 00:00:00 — Z (S) $7000.00

1910.132 A

Deleted Serious Gravity 10 2 instances 2 exposed

Issued: Apr 18, 2011
Abate by: May 20, 2011
Penalty: Initial $7,000 · Current $7,000

General-duty citation text

29 CFR 1910.132(a):
ADM Milling Co. - Lincoln, NE - Protective equipment was not used when
necessary whenever
hazards capable of causing injury and impairment were encountered.
Employee(s) involved in stopping a chlorine gas leak, wore gloves and
clothing
that were not impervious to chemicals.
Abatement certification and abatement documentation is required for this
violation. The
documentation should include written verification of abatement, applicable
measurements or
monitoring results, and photographs or videos which you believe will be
helpful. The abatement
certification sheet is enclosed with the citations.

Recent events (2)

2011-05-12 00:00:00 — I (S) $7000.00
2011-04-18 00:00:00 — Z (S) $7000.00

1910.151 C

Serious Gravity 05 2 instances 10 exposed

Issued: Apr 18, 2011
Abate by: May 21, 2011
Penalty: Initial $4,000 · Current $4,000

General-duty citation text

29 CFR 1910.151(c):
ADM Milling Co. - Lincoln, NE - Where employees were exposed to injurious
corrosive
materials, suitable facilities for quick drenching or flushing of the eyes
and body were not
provided within the work area for immediate emergency use.
Appropriate eyewash/shower station(s) were not provided in the chlorine
storage
room and 3rd floor agitator area. Employees were potentially exposed to
corrosive chlorine gas.
Abatement certification is required for this violation. The abatement
certification sheet is
enclosed with the citations.ion

Recent events (2)

2011-05-12 00:00:00 — I (S) $4000.00
2011-04-18 00:00:00 — Z (S) $4000.00

1910.1200 H03 II

Other-than-serious Gravity 05 1 instance 5 exposed

Issued: Apr 18, 2011
Abate by: Mar 16, 2011
Penalty: Initial $3,400 · Current $3,400

General-duty citation text

29 CFR 1910.1200(h)(3)(ii):
ADM Milling Co. - Lincoln, NE - Employee training did not include the
physical and health
hazards of the chemicals in the work area.
Employees, potentially exposed to hexavalent chromium from stainless steel
hot
work, had not been trained on its physical and health hazards.

Recent events (2)

2011-05-12 00:00:00 — I (O) $3400.00
2011-04-18 00:00:00 — Z (S) $3400.00

More inspections at ADM Milling CO.

Nov 26, 2024 SALINA, KS Feb 13, 2024 ABILENE, KS Feb 13, 2024 ABILENE, KS Feb 23, 2023 CHATTANOOGA, TN Aug 24, 2022 ARKANSAS CITY, KS

View ADM Milling CO.'s full OSHA safety record →

More inspections in this industry (NAICS 311211)

Jun 17, 2026 Grain Craft - Kansas City · KANSAS CITY, KS Jun 10, 2026 WA317991603 - GF Blends INC · RICHLAND, WA Jun 2, 2026 Continental Dairy Facilities Southwest, LLC · LITTLEFIELD, TX May 8, 2026 Didion Milling, INC. · CAMBRIA, WI Apr 22, 2026 111116 - Ardent Mills LLC · HASTINGS, MN

More inspections in NE

Jul 15, 2026 Smithfield Foods · CRETE, NE Jul 14, 2026 Laco Enterprises, LLC · OMAHA, NE Jul 10, 2026 Wingstop · OMAHA, NE Jul 1, 2026 Smithfield Packaged Meats Corp. · LINCOLN, NE Jun 30, 2026 Patriot Plumbing, Heating & AC · LINCOLN, NE

Source

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 314059460.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.