TOMBALL, TX —
OSHA Inspection: TRINITY STEEL FABRICATORS, INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of TRINITY STEEL FABRICATORS, INC. in 19902 HUFSMITH KOHRVILLE RD., TOMBALL, TX 77375 (NAICS 332996). OSHA activity number 315130922.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TRINITY STEEL FABRICATORS, INC.
- Site address
- 19902 HUFSMITH KOHRVILLE RD.
- City
- TOMBALL
- State
- TX
- ZIP
- 77375
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332996
- SIC code (legacy)
- 3498
- Employees
- 45
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Apr 8, 2011
- Abate by
- Apr 20, 2011
- Penalty
- Initial $4,900 · Current $4,900
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish to each of his employees a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of falling loads due to the lack of safety latches on hoist hooks. In fabrication facility, the employer did not ensure that overhead gantry cranes had operable safety latches on hooks. This condition exposed employees to crush-by hazards. 1) 5-Ton Crane; A-6673 2) 5-Ton Crane; A-2 3) 5-Ton Crane; P3115 4) 10-Ton Crane;B-5 Among other methods, one feasible and acceptable method for abatement is to this hazard is to have all safety latches repaired and adhere to the requirements of ASME B30.10-2009 and/or to comply with the manufacturer's equipment operating guidelines in order to protect employees from exposure to crush-by hazards. Disclaimers: 1. You are not limited to the abatement methods suggested above. 2. The methods explained are general and may not be effective in all cases. 3. The employer is responsible for selecting and carrying out an appropriate method.
1910.252 B02 III
- Issued
- Apr 8, 2011
- Abate by
- Apr 20, 2011
- Penalty
- Initial $2,800 · Current $2,800
1910.219 E03 I
- Issued
- Apr 8, 2011
- Abate by
- Apr 20, 2011
- Penalty
- Initial $4,900 · Current $4,900
1910.219 D01
- Issued
- Apr 8, 2011
- Abate by
- Apr 20, 2011
1904.29 B01
- Issued
- Apr 8, 2011
- Abate by
- Apr 27, 2011
- Penalty
- Initial $700 · Current $700
1904.29 B01
- Issued
- Apr 8, 2011
- Abate by
- Apr 27, 2011
- Penalty
- Initial $700 · Current $700
1904.29 B01
- Issued
- Apr 8, 2011
- Abate by
- Apr 27, 2011
- Penalty
- Initial $700 · Current $700
1904.29 B01
- Issued
- Apr 8, 2011
- Abate by
- Apr 27, 2011
- Penalty
- Initial $700 · Current $700
1910.303 B01 III
- Issued
- Apr 8, 2011
- Abate by
- Apr 13, 2011
More inspections at Trinity Steel Fabricators, INC.
View Trinity Steel Fabricators, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332996)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315130922.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.