BEAUMONT, TX —
OSHA Inspection: T. K. STANLEY, INC.
Accident-driven inspection · Safety discipline
At a glance
On , OSHA opened an accident-driven safety inspection of T. K. STANLEY, INC. in LAT: 30 06' 34.11103" - LONG: 94 16' 34.79731", BEAUMONT, TX 77713 (NAICS 238910). OSHA activity number 315258582.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- T. K. STANLEY, INC.
- Site address
- LAT: 30 06' 34.11103" - LONG: 94 16' 34.79731"
- City
- BEAUMONT
- State
- TX
- ZIP
- 77713
- Mailing
- 6739 HWY 184 , PO BOX 31, WAYNESBORO, MS 39367
What kind of inspection was it?
- Inspection type
- Accident-driven (A)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238910
- SIC code (legacy)
- 1389
- Employees
- 4
- Ownership type
- A
Citations
3 citations on file for this inspection.
5(a)(1)
- Issued
- Aug 15, 2011
- Abate by
- Aug 19, 2011
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish to each of his employees a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to the hazard of struck-by and caught-between when working around and working with rig derrick sections while rigging up: This violation occurred on or about March 19, 2011, at Maness Gas Unit # 6 site where employees were exposed to being struck-by and/or caught between rig derrick sections that were unloaded from a truck and set vertically on edge and side-by-side. One side of each section was supported by a protruding spreader beam with a pin connection hinge installed. This caused the section to lean toward the other side which was unsupported. Employees walking and/or working between the sections were exposed to a struck-by and /or caught-between hazard in the event of a section falling to the unsupported side as a result of the unstable positioning of the sections. Among other feasible methods to correct the identified hazard, comply with the American Petroleum Institute (API) Recommended Practice for Occupational Safety for Oil Well Drilling and Servicing Operations, API RP 54, recommendation to conduct a review, prior to commencing rig-up operations, of the planned arrangement of equipment placement to eliminate and/or minimize potentially hazardous conditions; place the derrick sections face down, when off loaded from the truck, to ensure that they are in a stable position. Pursuant to 29 CFR 1903.19, within ten (10) calendar days, the employer must submit documentation describing the actions it is taking to ensure that the placement of derrick sections unloaded from trucks are set in a stable position to prevent them from falling or being knocked over.ed
1904.32 B03
- Issued
- Aug 15, 2011
- Abate by
- Aug 18, 2011
- Penalty
- Initial $1,000 · Current $1,000
1904.32 B03
- Issued
- Aug 15, 2011
- Abate by
- Aug 18, 2011
- Penalty
- Initial $1,000 · Current $1,000
More inspections at T. K. Stanley, INC.
View T. K. Stanley, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238910)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315258582.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.