STURBRIDGE, MA ·
OSHA Inspection: SOUTHBRIDGE SHEET METAL WORKS, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of SOUTHBRIDGE SHEET METAL WORKS, INC. in 441 MAIN STREET, STURBRIDGE, MA 01518 (NAICS 332322). OSHA activity number 315514745.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- SOUTHBRIDGE SHEET METAL WORKS, INC.
- Site address
- 441 MAIN STREET
- City
- STURBRIDGE
- State
- MA
- ZIP
- 01518
- Mailing
- P.O. BOX 517, STURBRIDGE, MA 01566
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332322
- SIC code (legacy)
- 3444
- Employees
- 38
- Ownership type
- A
Citations
9 citations on file for this inspection.
5(a)(1)
- Issued
- Sep 15, 2011
- Abate by
- Sep 19, 2011
- Penalty
- Initial $2,975
General-duty citation text
Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm in that employees were exposed to possible falls and/or being struck and/or crushed by a manlift that may fall during use: (a) ESTABLISHMENT -- THE EMPLOYER DID NOT ENSURE THAT THE ONE (1) IN- HOUSE METAL-FABRICATED MANLIFT ATTACHED TO A PROPANE FORKLIFT TRUCK WAS APPROVED BY A QUALIFIED ENGINEER PRIOR TO EMPLOYEE(S) USING IT FOR MAINTENANCE PURPOSES. AMONG OTHER METHODS, ONE FEASIBLE AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THIS APPARENT HAZARD IS TO USE A PLATFORM THAT MEETS THE DESIGN REQUIREMENTS CONTAINED IN AMERICAN NATIONAL STANDARDS INSTITUTE ANSI B56.1-2005 ENTITLED "SAFETY STANDARD FOR LOW LIFT AND HIGH LIFT TRUCKS", IN PARTICULAR, COMPLY WITH THE FOLLOWING PROVISIONS OF THE STANDARD: 1. Have a qualified engineer evaluate the structural integrity of the platform, including the bent sections, to ensure that the platform has a structural safety factor of not less than 3 to 1 (ANSI B56.1-2005, paragraph 7.37.1(g). 2. Provide a means to securely attach the platform to the lifting carriage or forks of the fork truck (ANSI B56.1- 2005, paragraph 7.37.3(c)). 3. Ensure that the lifting platform is designed so that the floor of the platform that personnel stands on is not more than 200 mm (7.8 inches) above the level of the forks (ANSI B56.1-2005, paragraph 7.3.3(b). 4. Ensure that the maximum load including personnel and equipment, the weight of the empty platform, and the minimum capacity of the truck on which the platform can be used is prominently displayed on the platform. Note: The combined weight of the platform load and personnel cannot exceed one-half of the capacity of the fork truck on which the platform load is used. (ANSI B56.1-2005 paragraph 7.37.3(i). 5. There shall be a minimum floor space of 450 mm )18 inches) X 450 mm (18 inches) for each platform occupant.
Recent events (3)
- · I (S)
- · F (S)
- · Z (S) $2975.00
1910.132 D02
- Issued
- Sep 15, 2011
- Abate by
- Oct 18, 2011
- Penalty
- Initial $1,785
Recent events (2)
- · F (O)
- · Z (S) $1785.00
1910.184 D
- Issued
- Sep 15, 2011
- Abate by
- Sep 25, 2011
- Penalty
- Initial $2,380
Recent events (3)
- · F (O)
- · I (O)
- · Z (S) $2380.00
1910.184 D
- Issued
- Sep 15, 2011
- Abate by
- Sep 20, 2011
Recent events (2)
- · F (O)
- · Z (S)
1910.212 A03 II
- Issued
- Sep 15, 2011
- Abate by
- Nov 2, 2011
- Penalty
- Initial $2,975 · Current $1,487 Reduced
Recent events (3)
- · I (S) $1487.00
- · F (S) $1487.00
- · Z (S) $2975.00
1910.334 A02 II
- Issued
- Sep 15, 2011
- Abate by
- Sep 20, 2011
- Penalty
- Initial $2,975 · Current $975 Reduced
Recent events (3)
- · I (S) $975.00
- · F (S) $975.00
- · Z (S) $2975.00
1910.215 A04
- Issued
- Sep 15, 2011
- Abate by
- Sep 20, 2011
- Penalty
- Initial $2,023 · Current $1,000 Reduced
Recent events (3)
- · I (S) $1000.00
- · F (S) $1000.00
- · Z (S) $2023.00
1910.215 B09
- Issued
- Sep 15, 2011
- Abate by
- Sep 20, 2011
Recent events (2)
- · F (O)
- · Z (S)
1910.1200 E01
- Issued
- Sep 15, 2011
- Abate by
- Oct 18, 2011
- Penalty
- Initial $1,785
Recent events (2)
- · F (O)
- · Z (S) $1785.00
More inspections at Southbridge Sheet Metal Works, INC.
View Southbridge Sheet Metal Works, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332322)
More inspections in MA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 315514745.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.