REIDSVILLE, NC —
OSHA Inspection: ISOMETRICS, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of ISOMETRICS, INC. in 1266 N. SCALES ST, REIDSVILLE, NC 27320 (NAICS 332420). OSHA activity number 316472224.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- ISOMETRICS, INC.
- Site address
- 1266 N. SCALES ST
- City
- REIDSVILLE
- State
- NC
- ZIP
- 27320
- Mailing
- P.O. BOX 660, REIDSVILLE, NC 27323
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- N
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332420
- SIC code (legacy)
- 3499
- Employees
- 34
- Ownership type
- A
- Industry flags
- Manufacturing health.
Citations
5 citations on file for this inspection.
95012901
- Issued
- Jun 7, 2012
- Abate by
- Jun 12, 2012
- Penalty
- Initial $150 · Current $150
General-duty citation text
North Carolina General Statute 95-129(1) of the Occupational Safety and Health Act of North Carolina: The employer did not furnish to each of his employees conditions of employment and a place of employment free from recognized hazards that were causing or likely to cause death or physical harm to employees in that employees were exposed to being struck by falling loads: a)Facility - there were underhung cranes throughout the facility used to manipulate and move tanks and steel during the manufacturing process. The upper limit switches on the hoists were not tested without a load at the beginning of each work shift. REFERENCE: ANSI B30.11-1980, Section 11-2.1.2, Frequent Inspection. (b)Items such as the following shall be inspected at intervals as defined in 11-2.1.1(b)(1). Observation should be made during operation for any defects or damage which might appear between inspections. Any deficiencies, such as listed, shall be carefully examined, and a determination made as to whether they constitute a hazard: (1)All functional operating mechanisms for misadjustment interfering with proper operation. (2)All limit switches should be checked, without a load, on the hook, at the beginning of each work shift. Care shall be exercised. Each motion shall be inched to its limit switch or run in slow speeds. (3)Leakage in lines, tanks, valves, pumps, and other parts of pneumatic or hydraulic lines. NOTE: Among other means of abatement, one feasible and acceptable method to correct this hazard is to test the upper limit switches of all hoists at the beginning of each work shift.ing
Recent events (2)
- — I (S) $150.00
- — Z (S) $150.00
1910.132 A
- Issued
- Jun 7, 2012
- Abate by
- Jun 12, 2012
- Penalty
- Initial $250 · Current $150 Reduced
Recent events (2)
- — I (S) $150.00
- — Z (S) $250.00
1910.178 Q07
- Issued
- Jun 7, 2012
- Abate by
- Jun 12, 2012
1910.179 H04
- Issued
- Jun 7, 2012
- Abate by
- Jun 12, 2012
- Penalty
- Initial $150 · Current $100 Reduced
Recent events (2)
- — I (S) $100.00
- — Z (S) $150.00
1910.334 A02 II
- Issued
- Jun 7, 2012
- Abate by
- Jun 12, 2012
Recent events (2)
- — I (O)
- — Z (O)
More inspections at Isometrics, INC.
View Isometrics, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332420)
More inspections in NC
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 316472224.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.