OSHA Inspection: PANE STONE CONSTRUCTION INC.

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $3000.00 · Current $3000.00

General-duty citation text

29 CFR 1926.403(b)(2):     Listed, labeled, or certified equipment was not installed and used in accordance with instructions included in the listing, labeling, or certification:    (a) At the worksite - An outlet designed to be permanently mounted on or in a wall, was used to power a welder. The outlet was ratedat 240v 30Amps; on or about 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $3000.00 · Current $3000.00

General-duty citation text

29 CFR 1926.404(f)(6):     The path to ground from circuits, equipment, or enclosures was not permanent and continuous:    (a) At the worksite - A Makita Drill and Saws-all used to drill and cut wood did not have a ground prong on the plug at the end of the extension cord used to power the equipment; on or about 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $3000.00 · Current $3000.00

General-duty citation text

29 CFR 1926.405(b)(2):     All pull boxes, junction boxes, and fittings were not provided with covers:    (a) At the worksite - A service panel used to power equipment at the site had open slots for circuit breakers that were not covered;  03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $1800.00 · Current $1800.00

General-duty citation text

29 CFR 1926.1053(a)(2):     Ladder rungs, cleats, and/or steps were not parallel, level, and uniformly spaced when the ladder was in position for use:    a) At the work site -  Several wood job made ladders were constructed with rungs that were not parallel, level and uniformly spaced; on or 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 19

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.1053(a)(3)(i):     Rungs, cleats, and steps of portable ladders (except as provided below) and fixed ladders (including individual-rung/step ladders) shall be spaced not less than 10 inches (25 cm) apart, nor more than 14 inches (36 cm) apart, as measured between center lines of the rungs, cleats and steps.    a)  At the work site - Wood job-made ladders had rungs that were spaced 17 inches and 15 inches apart;  on or about 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19

Issued

2012-06-12 00:00:00

Abate by

2012-06-13 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.1053(b)(1): Because of the portable ladder's length, the ladder side rails did not extend to at least 3 feet (.9 m) above the upper landing surface to which the ladder was used to gain access and/or was not secured at its top to a rigid support:    (a) At the worksite - Several wood job-made ladders used to access the the top of the foundation from ground level were not secured and did not extend 3 feet above the upper landing; on or about 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19

Issued

2012-06-12 00:00:00

Abate by

2012-07-03 00:00:00

Penalty

Initial $0.00 · Current $0.00

General-duty citation text

29 CFR 1926.1060(a):     The employer did not provide a training program for each employee using ladders and stairways, as necessary, which would enable each employee to recognize hazards related to ladders and stairways and train each employee in the procedures to be followed to minimize these hazards.  	                             (a) At the worksite - Employees used wood job made ladders that were not secured, had rungs that were not parallel and uniformly spaced and had rungs that were spaced too far apart; on or about 03/02/12.    NOTE:  THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM IN THE ACCORDANCE WITH 29 CFR 1903.19