LUBBOCK, TX ·
OSHA Inspection: BRYAN BENNETT ENTERPRISES INC.
Programmed Other inspection · Safety discipline
At a glance
On , OSHA opened a programmed Other safety inspection of BRYAN BENNETT ENTERPRISES INC. in 6204 MILWAUKEE AVE, LUBBOCK, TX 79424 (NAICS 238120). OSHA activity number 334073624.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BRYAN BENNETT ENTERPRISES INC.
- Site address
- 6204 MILWAUKEE AVE
- City
- LUBBOCK
- State
- TX
- ZIP
- 79424
- Mailing
- 8101 FM 2641, SHALLOWATER, TX 79363
What kind of inspection was it?
- Inspection type
- Programmed Other (K)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238120
- Employees
- 4
- Ownership type
- Private (A)
Citations
5 citations on file for this inspection.
1926.350 A07
- Issued
- Jul 6, 2012
- Abate by
- Jul 13, 2012
- Penalty
- Initial $2,640 · Current $0 Reduced
General-duty citation text
29 CFR 1926.350(a)(7): A suitable cylinder truck, chain, or other steadying device was not used to keep cylinders from being knocked over while in use. 29 CFR 1926.350(a)(12): The in-plant handling, storage, and utilization of all compressed gases in cylinders, portable tanks, rail tankcars, or motor vehicle cargo tanks shall be in accordance with Compressed Gas Association Pamphlet P-1-1965. On or about 13 March at work site on 6204 Milwaukee Ave, compressed gas cylinder on north west side was not properly supported to prevent it from being knocked over, exposing employees to struck by hazard from high pressure projectile.
Recent events (2)
- · I (S) $0
- · Z (S) $2640
1926.351 B02
- Issued
- Jul 6, 2012
- Abate by
- Jul 13, 2012
- Penalty
- Initial $2,640 · Current $2,640
General-duty citation text
29 CFR 1926.351(b)(2): Only cable free from repair or splices for a minimum distance of 10 feet from the cable end to which the electrode holder was connected shall be used, except that cables with standard insulated connectors or with splices whose insulating quality is equal to that of the cable are permitted. On or about 13 March 2012 at work site on 6204 Milwaukee Ave, employees had used a welding cable with several splices with in the 10ft (3m) of the holder exposing them to electrical shock or electrocution.
Recent events (2)
- · I (O) $2640
- · Z (S) $2640
1926.451 B02
- Issued
- Jul 6, 2012
- Abate by
- Jul 13, 2012
- Penalty
- Initial $3,960 · Current $3,300 Reduced
General-duty citation text
29 CFR 1926.451(b)(2): Except as provided in paragraphs (b)(2)(i) and (b)(2)(ii) of this section, each scaffold platform and walkway was not at least 18 inches (46 cm) wide. On or about 13 March 2012 at work site on 6204 Milwaukee Ave, an employee was observed sitting on scissor lift guardrails making this a scaffold platform, in which a scaffold platform is a work surface, elevated above lower level. Guardrail would then have to meet the requirements of 1926.451(b) (scaffold platform construction). By bypassing the guardrail system the employee was exposed to a fall hazard of over 14 ft
Recent events (2)
- · I (S) $3300
- · Z (S) $3960
1926.451 G01 VII
- Issued
- Jul 6, 2012
- Abate by
- Jul 13, 2012
- Penalty
- Initial $4,620 · Current $3,300 Reduced
General-duty citation text
29 CFR 1926.451(g)(1)(vii): For all scaffolds not otherwise specified in paragraphs (g)(1)(i) through (g)(1)(vi) of this section, each employee was not protected by the use of personal fall arrest systems or guardrail systems meeting the requirements of paragraph (g)(4) of this section. On or about 13 March at work site on 6204 Milwaukee Ave, two employees were observed working on elevated work surface and were not protected from fall hazards due to not being tied of to an anchor point. a. One employee sitting on guardrails of scissor lift was wearing fall arrest system but was not tied off b. 2nd employee standing outside of scissor lift on a metal beam was not tied off
Recent events (2)
- · I (S) $3300
- · Z (S) $4620
1926.761 C02 II
- Issued
- Jul 6, 2012
- Abate by
- Jul 13, 2012
- Penalty
- Initial $4,620 · Current $0 Reduced
General-duty citation text
29 CFR 1926.761(c): Special training programs. In addition to the training required in paragraphs (a) and (b) of this section, the employer did not provide special training to employees engaged in the following activities...1926.761(c)(1)-(c)(3) 29 CFR 1926.761(c)(1): Multiple lift rigging procedure. 29 CFR 1926.761(c)(2): Connector procedures. 29 CFR 1926.761(c)(3): Controlled Decking Zone Procedures. On or about 13 March 2012 the employer did not ensure that employees were trained in and familiar with the safety related practices that pertain to their respective job assignments in steel erection.
Recent events (2)
- · I (S) $0
- · Z (S) $4620
More inspections at Bryan Bennett Enterprises INC.
View Bryan Bennett Enterprises INC.'s full OSHA safety record →
More inspections in this industry (NAICS 238120)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 334073624.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.