ARLINGTON, TX —
OSHA Inspection: JAVIER FLORES
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of JAVIER FLORES in 5601 ALICANTE DR, ARLINGTON, TX 76017 (NAICS 238160). OSHA activity number 334148632.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- JAVIER FLORES
- Site address
- 5601 ALICANTE DR
- City
- ARLINGTON
- State
- TX
- ZIP
- 76017
- Mailing
- 100 W CASON ST, IRVING, TX 75061
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238160
- Employees
- 5
- Ownership type
- A
Citations
3 citations on file for this inspection.
1926.307 A02
- Issued
- Oct 25, 2012
- Abate by
- Oct 30, 2012
- Penalty
- Initial $2,000 · Current $2,000
General-duty citation text
29 CFR 1926.307(a)(2): Vertical and inclined belts (paragraphs (e)(3) and (4) of this section) if not more than 2 1/2 inches (6.35 cm) wide and running at a speed of less than one thousand (1,000) feet per minute, and if free from metal lacings or fastening were not guarded with a nip-point belt and pulley guard. On or about May 02, 2012, the employer did not ensure that the belt of the Honda Air Compressor was guarded. The employees were exposed to an ingoing nip point hazard.
Recent events (1)
- — Z (S) $2000
1926.307 D01
- Issued
- Oct 25, 2012
- Abate by
- Oct 30, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.307(d)(1): Pulley(s) with part(s) seven feet (2.128 m) or less from the floor or work platform were not guarded in accordance with the requirements specified in paragraphs (m) and (o) of this section: Note: Pulleys serving as balance wheels (e.g., punch presses) on which the point of contact between belt and pulley is more than 6 ft. 6 in. (1.976 m) from the floor or platform may be guarded with a disk covering the spokes. On or about May 02, 2012, the employer did not ensure that the pulley of the Honda Air Compressor was guarded. The employees were exposed to an ingoing nip point hazard.
Recent events (1)
- — Z (S) $0
1926.501 B13
- Issued
- Oct 25, 2012
- Abate by
- Oct 30, 2012
- Penalty
- Initial $2,000 · Current $2,000
General-duty citation text
29 CFR 1926.501(b)(13): Each employee engaged in residential construction activities 6 feet or more above lower levels was not protected by guardrail systems, safety net systems, or personal fall arrest systems, nor did the employer demonstrate that it is infeasible or creates a greater hazard to use these systems and develop and implement a fall protection plan which meets the requirements of paragraph (k) of section 1926.502. On or about May 02, 2012, employees who were installing roofing material were not provided fall protection. The employees were exposed to falls of 8 feet 2 inches to the ground below.
Recent events (1)
- — Z (S) $2000
More inspections at Javier Flores
View Javier Flores's full OSHA safety record →
More inspections in this industry (NAICS 238160)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 334148632.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.