SAN ANTONIO, TX —
OSHA Inspection: TWC ARCHITECTURAL MOULDINGS
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of TWC ARCHITECTURAL MOULDINGS in 8523 NE LOOP 410, SAN ANTONIO, TX 78219 (NAICS 321113). OSHA activity number 335523981.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- TWC ARCHITECTURAL MOULDINGS
- Site address
- 8523 NE LOOP 410
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78219
- Mailing
- 8523 NE LOOP 410, SAN ANTONIO, TX 78219
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321113
- Employees
- 29
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 D04 I
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: Gang Rip, Model 524-DC/SR4, S/N:MJ-7377, On or about 8/2/12 and at times prior thereto employees were exposed to an amputation hazard when bypassing a guard and removing dust from the dust collector.
Recent events (2)
- — I (S) $2100
- — Z (S) $3500
1910.157 C01
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $2,100 · Current $1,260 Reduced
General-duty citation text
29 CFR 1910.157(c)(1): Portable fire extinguishers were not mounted, located and identified so that they were readily accessible without subjecting the employees to injuries: On or about 8/2/12 and at times prior thereto, in case of an emergency, employees were exposed to a trip hazard from several boards that were stacked in front of the fire extinguisher.
Recent events (2)
- — I (S) $1260
- — Z (S) $2100
1910.212 A01
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: Prime Area, ENCO Milling Machine Model: 100-1599, S/N 10502: On or about 8/2/12 and at times prior thereto employees were exposed to an amputation hazard when milling keyways into shafts measuring approximately 5" in length by 1.5" diameter.
Recent events (2)
- — I (S) $2100
- — Z (S) $3500
1910.212 B
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving: Prime Area, ENCO Milling Machine Model: 100-1599, S/N 10502: On or about 8/2/12 and at times prior thereto employees were exposed to an amputation hazard when milling keyways into shafts measuring approximately 5" in length by 1.5" diameter.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 C04 I
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Unguarded projecting shaft end(s) did not present a smooth edge and end and projected more than one half the diameter of the shaft: a) Near the Rough Mill, On or about 8/2/12 and at times prior thereto employees were exposed to a rotating shaft measuring approximately 1 in. length x 3 in. diamter and containing a set screw, while stacking material from the mill. b) Near the Weinig Gruppe Power, Model: Power Pat-500 S/N 107444: On or about 8/2/12 and at times prior thereto employees were exposed to a rotating shaft measuring approximately 6 in. length by 1 in. diameter when stacking wood mouldings.
Recent events (2)
- — I (S) $2100
- — Z (S) $3500
1910.303 B02
- Issued
- Sep 6, 2012
- Abate by
- Sep 21, 2012
- Penalty
- Initial $3,500 · Current $2,100 Reduced
General-duty citation text
29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling: Prime Area, On or about 8/2/12 and at times prior thereto employees were exposed to an electrical shock of 120 volts from a junction box that was being used as an outlet.
Recent events (2)
- — I (S) $2100
- — Z (S) $3500
More inspections at TWC Architectural Mouldings
View TWC Architectural Mouldings's full OSHA safety record →
More inspections in this industry (NAICS 321113)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 335523981.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.