Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: RUSSEL METALS WILLIAMS BAHCALL INC.

Referral inspection · Safety discipline

On , OSHA opened a referral safety inspection of RUSSEL METALS WILLIAMS BAHCALL INC. in 999 W. ARMOUR AVE., MILWAUKEE, WI 53221 (NAICS 423510). OSHA activity number 336800792.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Russel Metals Williams Bahcall INC. — free Get an email when a new federal OSHA severe-injury report for Russel Metals Williams Bahcall INC. is published. One employer, no account, unsubscribe in one click.
Site address
999 W. ARMOUR AVE.
City
MILWAUKEE
State
WI
ZIP
53221
Mailing
999 W. ARMOUR AVE., MILWAUKEE, WI 53221
Inspection type
Referral (C)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
A
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
423510
Employees
85
Ownership type
A

2 citations on file for this inspection.

5(a)(1)

Serious Gravity 10 1 instance 44 exposed
Issued
Jan 2, 2013
Abate by
Jan 22, 2013
Penalty
Initial $7,000 · Current $4,900 Reduced
OSH ACT of 1970 Section (5)(a)(1):     Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which was free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to crushing and struck by hazards.    (a) Bay 3 Center: A Walker lifting magnet used to handle steel sheet plate did not have the rated load capacity, weight of lifting magnet, duty cycle and other required identification information marked/affixed to the lifting device. This exposed the employee(s) to a crushing hazard.    (b) Bay 3 South: A Walker lifting magnet used to handle steel sheet plate did not have the rated load capacity, weight of lifting magnet, duty cycle and other required identification information marked/affixed to the lifting device. This exposed the employee(s) to a crushing hazard.    (c) Bay 2 North: Crane Operator(s) while operating Bay 2 North overhead crane did not remain a safe distance from the load when operating and adjusting the load being lifted. The operator stood/crouched directly next to the mechanical sheet lifter while manipulating the sheet lifter to secure the sheet lifter around sheet pile to be lifted. This exposed the operator to a struck by and crushing hazard.
Recent events (2)
  • — I (S) $4900
  • — Z (S) $7000

1910.179 J02

Deleted Other-than-serious 2 instances 44 exposed
Issued
Jan 2, 2013
Penalty
Initial $0 · Current $0
29 CFR 1910.179(j)(2):     The following items were not be inspected for defects at intervals as defined in paragraph (j)(1)(ii) of this section or as specifically indicated, including observation during operation for any defects which might appear between regular inspections:    (a) Bay 3 North Crane: frequent inspections of crane hooks are not being performed on a daily schedule or before each shift. Hook was identified to have broken spring latch that was not replaced and or repaired.    (b) Bay 3 Center Crane: frequent inspections of crane hooks are not being performed on a daily schedule or before each shift. Hook was identified to have broken spring latch that was not replaced and or repaired.
Recent events (2)
  • — I (O) $0
  • — Z (O) $0

View Russel Metals Williams Bahcall INC.'s full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 336800792.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.