LINDEN, NJ —
OSHA Inspection: WELL BILT INDUSTRIES, INC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of WELL BILT INDUSTRIES, INC in 2 MAPLE AVENUE, LINDEN, NJ 07036 (NAICS 332116). OSHA activity number 338938327.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- WELL BILT INDUSTRIES, INC
- Site address
- 2 MAPLE AVENUE
- City
- LINDEN
- State
- NJ
- ZIP
- 07036
- Mailing
- 2 MAPLE AVENUE, LINDEN, NJ 07036
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332116
- Employees
- 8
- Ownership type
- A
Citations
2 citations on file for this inspection.
1910.147 C01
- Issued
- May 6, 2013
- Abate by
- May 31, 2013
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: a) Well Bilt Industries Linden, NJ site - Machine Shop: The employer did not establish an Energy Control program that defines machine specific energy control procedures, training and periodic inspections for employees performing part change out, maintenance and/or servicing machines to prevent accidental energizing of the machines. Machinery including but not limited to the Bliss punch presses did not have written procedures for de-energizing, and isolating energy sources. Condition noted on or about 3/6/2013. NOTE: THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM. FAILURE TO COMPLY WILL RESULT IN AN ADDITIONAL PENALTY OF $1000.00 IN ACCORDANCE WITH 29 CFR 1903.19.
Recent events (2)
- — I (S) $1400
- — Z (S) $2800
1910.212 A03 II
- Issued
- May 6, 2013
- Abate by
- May 31, 2013
- Penalty
- Initial $2,800 · Current $1,400 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone during the operating cycle: a) Well Bilt Industries Linden, NJ site - Machine Shop: Employees operating the Bliss punch presses were exposed to amputation hazards created by unguarded points of operation. Condition noted on or about 3/6/2013. NOTE: THE EMPLOYER IS REQUIRED TO SUBMIT ABATEMENT CERTIFICATION FOR THIS ITEM. FAILURE TO COMPLY WILL RESULT IN AN ADDITIONAL PENALTY OF $1000.00 IN ACCORDANCE WITH 29 CFR 1903.19.
Recent events (2)
- — I (S) $1400
- — Z (S) $2800
More inspections at Well Bilt Industries, INC
View Well Bilt Industries, INC's full OSHA safety record →
More inspections in this industry (NAICS 332116)
More inspections in NJ
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 338938327.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.