FORT CALHOUN, NE —
OSHA Inspection: D&W FINE PACK, LLC .
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of D&W FINE PACK, LLC . in 1112 MADISON STREET, FORT CALHOUN, NE 68023 (NAICS 326199). OSHA activity number 338949159.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- D&W FINE PACK, LLC .
- Site address
- 1112 MADISON STREET
- City
- FORT CALHOUN
- State
- NE
- ZIP
- 68023
- Mailing
- 1112 MADISON STREET, FORT CALHOUN, NE 68023
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 326199
- Employees
- 100
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.23 C01
- Issued
- May 3, 2013
- Abate by
- May 30, 2013
- Penalty
- Initial $4,675 · Current $3,038 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent) and toeboards: In the Drying Room at D&W Fine Pack 1112 Madison Street, Fort Calhoun, NE: The employer failed to ensure that open sided platforms and or floors greater than four feet ( 48 inches) above adjacent floors were guarded with a standard railing or equivalent.
Recent events (2)
- — I (S) $3038
- — Z (S) $4675
1910.23 E02
- Issued
- May 3, 2013
- Abate by
- May 30, 2013
- Penalty
- Initial $2,805 · Current $1,823 Reduced
General-duty citation text
29 CFR 1910.23(e)(2): Stair rails did not consist of a top rail, intermediate rail and/or posts, with the vertical height not more than 34 inches (86.36 cm) nor less than 30 inches (76.2 cm) from upper surface of top rail to surface of tread in line with In the Plastic Molding Area on the #10 Machine: The employer failed to provide an intermediate rail on the stair platform to the #10 Molding Machine.
Recent events (2)
- — I (S) $1823
- — Z (S) $2805
1910.212 A01
- Issued
- May 3, 2013
- Abate by
- Jun 21, 2013
- Penalty
- Initial $7,000 · Current $4,550 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: At D&W Fine Pack in Maintenance and in the Tooling Areas: The employer failed to ensure that guarding was provided on machinery such as but not limited to drill presses, milling machines and lathes. Such instances include: a) 12 Dayton Drill Press, serial # 0b120011 (tool and die) b) Clausing Drill Press, unknown serial # (maintenance) c) Bridgeport Milling Machine, serial# 163799 (maintenance) d) 2- Moore Tools Milling Machines, serial# unknown (maintenance)
Recent events (2)
- — I (S) $4550
- — Z (S) $7000
1910.215 B09
- Issued
- May 3, 2013
- Abate by
- May 3, 2013
- Penalty
- Initial $4,675 · Current $3,038 Reduced
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: In the Tooling Area: The employer failed to ensure that the tongue guard on the Admiral 2HP Bench Grinder Serial # GW48851.2 was adjusted within one fourth of an inch from the surface of the abrasive wheel to the guard.
Recent events (2)
- — I (S) $3038
- — Z (S) $4675
1910.305 G01 IV
- Issued
- May 3, 2013
- Abate by
- May 30, 2013
- Penalty
- Initial $3,740 · Current $2,431 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv): Flexible cords were used in a manner not permitted in paragraph (g)(1)(ii): In the Foil Tool Prep Area: The employer failed to ensure that a 480v flexible cord pendant was used in a permissible manner in that: 1. The pendant was connected via plastic zip ties to the metal rafter in the ceiling 2. The flexible cord was not continuous run 3. The flexible cord was used for a substitute for permanent power
Recent events (2)
- — I (S) $2431
- — Z (S) $3740
More inspections at D&W Fine Pack, LLC .
View D&W Fine Pack, LLC .'s full OSHA safety record →
More inspections in this industry (NAICS 326199)
More inspections in NE
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 338949159.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.