OSHA Inspection: CLEARWOOD CUSTOM CARPENTRY & MILLWORK, LLC

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $1,785 · Current $893 Reduced

General-duty citation text

29 CFR 1910.22(b)(1): Aisles and passageways were not kept clear and in good repair, with no obstruction across or in aisles that could create a hazard:    a)  Custom/Commercial Dept., on or about 4/10/13:   Two four way receptacle outlets each with a three way airline connector protruding from the floor created a tripping hazard.    Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.22(c): Covers and/or guardrails were not provided to protect personnel from the hazards of open pits, tanks, vats, ditches, etc.:  a)  Electrical/Compressor Room, on or about 4/10/13:  Floor drain was not adequately guarded in that the opening measured approx. 16" X 9" X 9" deep.  Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $2,380 · Current $1,190 Reduced

General-duty citation text

29 CFR 1910.107(b)(5)(iv): Space within the spray booth on the downstream and upstream sides of filters were not protected with approved automatic sprinklers:    a)  Finishing Dept., Drying Area, on or about 4/10/13:  A spray booth used for spraying stains was not provided with automatic sprinklers.    Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $2,380 · Current $1,190 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:     a)  Tool Room, on or about 4/10/13:  Rotating chuck on a Ryobi drill press and a Central Machinery drill press were not guarded.     b)  Custom Shop, on or about 4/10/13:  Rotating chuck and spindle on a Clausing drill press were not guarded.     c)  Box Assembly, on or about 4/10/13:  Rotating chuck on a Central Machinery drill press was not guarded.     d)  Box Assembly, on or about 4/10/13:  Unused portion of blade on a Jet horizontal bandsaw was not guarded.     e)  Custom/Commercial Shop, on or about 4/10/13:  Rotating chuck on a Jet drill press was not guarded.     Abatement certification must be submitted for these items.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving:  a)  Custom/Commercial Dept., on or about 4/10/13:  A Jet drill press was not anchored to prevent walking or moving.  Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(p)(4): Belt sanding machinery was not provided with a guard at each nip point where the sanding belt ran onto a pulley, to prevent the operator's hands or fingers from coming into contact with nip points:  a)  Custom/Commercial Dept., on or about 4/10/13:  Ingoing nip points on a Powermatic edge sander were not adequately guarded.  Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $2,380 · Current $1,190 Reduced

General-duty citation text

29 CFR 1910.213(a)(9): All belts, pulleys, gears, shafts, and moving parts were not guarded in accordance with the specific requirements of 1910.219:    a)  Box Assembly, on or about 4/10/13:  V belt and pulleys driving a Jet horizontal bandsaw were not guarded.    Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $1,785 · Current $893 Reduced

General-duty citation text

29 CFR 1910.215(a)(2): Abrasive wheel(s) used on grinding machinery were not provided with safety guard(s) which covered the spindle end, nut, flange projections:    a)  Box Assembly, on or about 4/10/13:  Dayton bench grinder was not provided safety guards over the spindle end, nut and flange projections.    Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(a)(4): Grinding machinery was not used with work rest(s) to support offhand grinding work:  a)  Box Assembly, on or about 4/10/13:  Dayton bench grinder was not provided with a work rest for the right abrasive wheel.  Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(b)(9): Guard for abrasive wheel machine where the operator stands in front of the machine was not constructed so that the peripheral protecting member could be adjusted to the constantly decreasing diameter of the wheel:  a)  Box Assembly, on or about 4/10/13:  Dayton bench grinder was not provided with a tongue guard for the right abrasive wheel.  Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $1,785 · Current $0 Reduced

General-duty citation text

29 CFR 1910.305(b)(1)(ii): Unused openings in cabinets, boxes, and fittings were not effectively closed:    a)  Electrical/Compressor Room, on or about 4/10/13:  A duplex receptacle outlet had two knockouts missing.    Abatement certification must be submitted for this item.

Issued

Apr 18, 2013

Abate by

May 23, 2013

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(b)(2)(i): Pull boxes, junction boxes, and fittings were not provided with covers approved for the purpose:  a)  Electrical/Compressor Room, on or about 4/10/13:  A junction box had a cover missing.  Abatement certification must be submitted for this item.