Safety Incidents OSHA Severe Injury Reports · 2015–2025
5,189,992Inspections Most recent open 2026-07-18 Last loaded 2026-07-22

OSHA Inspection: SMITHCO CONSTRUCTION INC.

Planned inspection · Safety discipline

On , OSHA opened a planned safety inspection of SMITHCO CONSTRUCTION INC. in CORNER OF SAM HOUSTON AVE. & 18TH ST., ODESSA, TX 79761 (NAICS 237110). OSHA activity number 339084832.

What this inspection record means

OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.

Watch Smithco Construction INC. — free Get an email when a new federal OSHA severe-injury report for Smithco Construction INC. is published. One employer, no account, unsubscribe in one click.
Site address
CORNER OF SAM HOUSTON AVE. & 18TH ST.
City
ODESSA
State
TX
ZIP
79761
Mailing
P.O. BOX 45, CABALLO, NM 87931
Inspection type
Planned (H)
Scope
Partial (B)
Discipline
Safety
Advance notice
No
Union status
B
Opened
Closing conference
Case closed
Last modified
Data loaded
NAICS code
237110
Employees
5
Ownership type
A

4 citations on file for this inspection.

1926.652 A01

Serious Gravity 10 1 instance 2 exposed
Issued
Aug 21, 2013
Abate by
Oct 11, 2013
Penalty
Initial $5,390 · Current $3,773 Reduced
29 CFR 1926.652(a)(1): Each employee in an excavation was not protected from cave-ins by an adequate protective system designed in accordance with paragraph (b) or (c) of this section:    On or about May 20, 2013, excavation site, employees working on one end of The L-shaped excavation/trench (approximately 30-feet in total length) did not have cave-in protective equipment. The excavation section, in which employees were working, was 7-foot deep, 7-foot wide and 8-foot 6-inches in length. This condition exposed employees to crush by cave-in hazards.
Recent events (2)
  • — I (S) $3773
  • — Z (S) $5390

1926.651 J02

Serious Gravity 10 2 instances 2 exposed
Issued
Aug 21, 2013
Abate by
Oct 11, 2013
Penalty
Initial $0 · Current $0
29 CFR 1926.651(j)(2): Employees were not protected from excavated or other materials or equipment that could pose a hazard by falling or rolling into excavations, or by a combination of both if necessary:     On or about May 20, 2013, excavation site, the L-shaped excavation/trench approximately 30-feet in total length had the spoil piles set too close to the edge. This condition exposed employees to spoils and equipment rolling back on top of workers and cave-in hazards.      a)    The excavation section, in which employees were working, was 7-foot deep, 8-feet 6-inch in length, 7-foot wide had the spoil pile set 21-inches from the edge.       b)    The trenched section (the only egress passageway) was 15-feet long, 4-feet wide; 5-foot 4-inches deep had the spoil pile set at the edge.
Recent events (2)
  • — I (S) $0
  • — Z (S) $0

1926.651 C

Serious Gravity 10 1 instance 2 exposed
Issued
Aug 21, 2013
Abate by
Oct 11, 2013
Penalty
Initial $5,390 · Current $3,773 Reduced
29 CFR 1926.651(c): A stairway, ladder, ramp or other safe means of egress was not located in trench excavations that are 4 feet (1.22 m) or more in depth so as to require no more than 25 feet (7.62 m) of lateral travel for employees:    On or about May 20, 2013, excavation site, employees working on one end of the L-shaped excavation/trench (approximately 30-feet in total length) did not have a safe means of egress within 25 feet from where they were working. This condition exposed employees to fall hazards.
Recent events (2)
  • — I (S) $3773
  • — Z (S) $5390

1926.300 B01

Serious Gravity 1 1 instance 1 exposed
Issued
Aug 21, 2013
Abate by
Oct 11, 2013
Penalty
Initial $2,310 · Current $1,617 Reduced
29 CFR 1926.300(b)(1): Power operated tool(s), designed to accommodate guards, were not equipped with such guards when in use:      On or about May 23, 2013, excavation site, an Angle Grinder (Model D28402 - Serial No. 2363) used by employees to grind down pipe spurs/welds did not have a guard. Employees were exposed to struck-by hazards.
Recent events (2)
  • — I (S) $1617
  • — Z (S) $2310

View Smithco Construction INC.'s full OSHA safety record →

This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339084832.

Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.