EVANS, GA ·
OSHA Inspection: QG PRINTING II CORP.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of QG PRINTING II CORP. in 4301 EVANS TO LOCKS RD., EVANS, GA 30809 (NAICS 323111). OSHA activity number 339425936.
OSHA opens inspections for many reasons: routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- QG PRINTING II CORP.
- Site address
- 4301 EVANS TO LOCKS RD.
- City
- EVANS
- State
- GA
- ZIP
- 30809
- Mailing
- 4301 EVANS TO LOCKS RD., EVANS, GA 30809
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- Non-union (B)
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 323111
- Employees
- 563
- Ownership type
- Private (A)
Citations
4 citations on file for this inspection.
5(a)(1)
- Issued
- Jan 28, 2014
- Penalty
- Initial $7,000 · Current $0 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees: On or about September 24, 2013, employees were exposed to struck-by hazards while performing work around damaged racks. The employer failed to unload, replace or properly repair damaged racks. The following racks were damaged: Corner rack on the aisle near the pressroom. AMONG OTHER METHODS, ONE FEASIBLE AND ACCEPTABLE ABATEMENT METHOD TO CORRECT THESE HAZARDS IS: To follow American National Standard Institute (ANSI) MH16.1:2012, Specification for the Design, Testing, and Utilization of Industrial Storage Racks, Section 1.4.9, which states, "Upon any visible damage, the pertinent portions of the rack shall be immediately isolated by the user until the damaged portion is evaluated by a storage rack design professional. Before allowing the rack to be placed back into service the design professional must certify that the rack system and/or the repaired components have been restored to at least their original design capacity.
Recent events (3)
- · F (S) $0
- · C (S) $7000
- · Z (S) $7000
1910.106 E06 I
- Issued
- Jan 28, 2014
- Abate by
- Feb 3, 2014
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
29 CFR 1910.106(e)(6)(i): Adequate precautions were not taken to prevent the ignition of flammable vapors: On or about September 17, 2013, employees were exposed to burn hazards when the employees were permitted to work in the press room with the equipment running and while using acetone to correct a printing defect without insuring that there were no sources of ignition.
Recent events (3)
- · F (S) $7000
- · C (S) $7000
- · Z (S) $7000
1910.132 A
- Issued
- Jan 28, 2014
- Abate by
- Feb 24, 2014
- Penalty
- Initial $7,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.132(a): Protective equipment was not provided when necessary whenever hazards capable of causing injury and impairment were encountered: On or about September 17, 2013, employees were exposed to burn hazards when the employees were permitted to work in the press room without protection from burns for the head, face, arms, and hands.
Recent events (3)
- · F (S) $0
- · C (S) $7000
- · Z (S) $7000
1910.212 A01
- Issued
- Jan 28, 2014
- Abate by
- Feb 3, 2014
- Penalty
- Initial $7,000 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and On or about August 26, 2013, employees were exposed to amputation hazards when the guard on the front of the de-stacker on the palletizing machine was easily removed by lifting up on the guard which permitted access to the point of operation behind the guard.
Recent events (3)
- · F (S) $0
- · C (S) $7000
- · Z (S) $7000
More inspections at QG Printing II Corp.
View QG Printing II Corp.'s full OSHA safety record →
More inspections in this industry (NAICS 323111)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). OSHA publishes its own view of this case as inspection number 339425936.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.