FRANKLIN, GA —
OSHA Inspection: JAC PRODUCTS, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of JAC PRODUCTS, INC. in 266 MARY JOHNSON DRIVE, FRANKLIN, GA 30217 (NAICS 331316). OSHA activity number 339805913.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- JAC PRODUCTS, INC.
- Site address
- 266 MARY JOHNSON DRIVE
- City
- FRANKLIN
- State
- GA
- ZIP
- 30217
- Mailing
- 266 MARY JOHNSON DRIVE, FRANKLIN, GA 30217
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 331316
- Employees
- 504
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.23 A09
- Issued
- Sep 25, 2014
- Penalty
- Initial $4,000 · Current $2,400 Reduced
General-duty citation text
29 CFR 1910.23(a)(9): Every floor hole into which persons cannot accidentally walk (on account of fixed machinery, equipment or walls) shall be protected by a cover that leaves no openings more than 1 inch wide. The cover shall be securely held in place to prevent tools or materials from falling through: a) Production Area: The employer failed to cover/fill in holes by the extruders in the Production Area, which measured 3 inches wide, exposing walking employees and powered industrial truck operators to tripping hazards. b) Production Area/Dock door leading to back of the facility : The employer failed to cover/fill in gap leading from the Production Area to exit door, which measured 2 inches wide, exposing walking employees to tripping hazards. c) Production Area: The employer failed to cover/fill in holes in the area of Press #2 on the Production floor, which measured 3 inches wide, exposing the employees and powered industrial truck operators to tripping hazards.
Recent events (2)
- — I (S) $2400
- — Z (S) $4000
1910.110 E04 III
- Issued
- Sep 25, 2014
- Penalty
- Initial $5,000 · Current $3,000 Reduced
General-duty citation text
29 CFR 1910.110(e)(4)(iii): Permanent and removable fuel containers were not securely mounted to prevent jarring loose, slipping, or rotating: a) Production Area: The employer failed to ensure that a LP gas cylinder was secured on the Hyundai #25C-5E powered industrial truck. The latch designed to secure the cylinder was broken. The PIT operator was exposed to a struck by hazard while operating the industrial truck to move automotive parts in and around the process area.
Recent events (2)
- — I (S) $3000
- — Z (S) $5000
1910.179 B05
- Issued
- Sep 25, 2014
- Penalty
- Initial $7,000 · Current $4,200 Reduced
General-duty citation text
29 CFR 1910.179(b)(5): The rated load of crane(s) was not plainly marked on each side of the crane: a) Production Area: The employer had recently painted the arms of cranes and failed to ensure the rating load was plainly marked on each side of the DEMAG 5 ton crane, exposing the employees to struck by hazard.
Recent events (2)
- — I (S) $4200
- — Z (S) $7000
1926.1053 B16
- Issued
- Sep 25, 2014
- Penalty
- Initial $7,000 · Current $4,200 Reduced
General-duty citation text
29 CFR 1926.1053(b)(16): Portable ladders with structural defects, such as, but not limited to, broken or missing rungs, cleats, or steps, broken or split rails, corroded components, or other faulty or defective components, were not either immediately marked in a manner that readily identifies them as defective, or tagged with "Do Not Use" or similar language, and were not withdrawn from service until repaired. (a) Caustic Die Room/Production floor: The employer allowed an employee to work from a ladder that was defective, exposing the employee to fall hazard.
Recent events (2)
- — I (S) $4200
- — Z (S) $7000
More inspections at JAC Products, INC.
View JAC Products, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 331316)
More inspections in GA
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 339805913.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.