CUBA, MO —
OSHA Inspection: OZARK MOUNTAIN TECH INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of OZARK MOUNTAIN TECH INC. in 106 MIDLAND DRIVE, CUBA, MO 65453 (NAICS 332813). OSHA activity number 340060649.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- OZARK MOUNTAIN TECH INC.
- Site address
- 106 MIDLAND DRIVE
- City
- CUBA
- State
- MO
- ZIP
- 65453
- Mailing
- 106 MIDLAND DRIVE, CUBA, MO 65453
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332813
- Employees
- 139
- Ownership type
- A
Citations
6 citations on file for this inspection.
5(a)(1)
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $5,500 · Current $5,500
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employee(s) in that employee(s) were exposed to the hazard of being struck-by: Inside of the Maintenance Department, the blue and grey, metal shelving units were not anchored or otherwise secured. One method of abatement to correct this apparent hazard is to anchor each shelving unit with a sufficient number of column base plates and anchor bolts as required by ANSI MH16.1-2012, paragraph 1.4.7. DISCLAIMER: a/ The employer is not limited to the abatement method(s) suggested by OSHA. b/ The employer is responsible for selecting and implementing an effective abatement method.
Recent events (2)
- — I (S) $5500
- — Z (S) $5500
1910.147 C04 II
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $5,500 · Current $0 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(ii): The procedures did not clearly and specifically outline the scope, purpose, authorization, rules, and techniques to be utilized for the control of hazardous energy, and the means to enforce compliance: a/ The specific lockout/tagout procedures for the boilers and ovens failed to address heat as an energy source or the amount of time that must transpire before servicing work can begin.
Recent events (2)
- — I (S) $0
- — Z (S) $5500
1910.147 C06 I
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirements of this standard are being followed: a/ Periodic audits of the specific procedures for the boilers and ovens were not performed.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $5,500 · Current $0 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: a/ Inside of the Maintenance Department, the spindle and chuck belonging to the Maxport Milling Machine, unknown m/n, s/n 44846, were unguarded.
Recent events (2)
- — I (S) $0
- — Z (S) $5500
1910.305 B01 II
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $5,500 · Current $5,500
General-duty citation text
29 CFR 1910.305(b)(1)(ii): Unused openings in cabinets, boxes, and fittings were not effectively closed: a/ Inside of the Maintenance Department, the quad-receptacle box supplying electrical power to a variety of machines such as an abrasive wheel grinder and buffer machine was missing a knockout.
Recent events (2)
- — I (O) $5500
- — Z (S) $5500
1910.334 A02 II
- Issued
- Dec 1, 2014
- Abate by
- Jan 20, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.334(a)(2)(ii): If there is a defect or evidence of damage that might expose an employee to injury, the defective or damaged item was not removed from service, and no employee may use it until repairs and tests necessary to render the equipment safe have been made: a/ Inside of the Maintenance Department, the outer insulation belonging to the flexible cord supplying electrical power to the Amada Horizontal Band Saw, m/n HA250, s/n 25400279, was damaged.
Recent events (2)
- — I (O) $0
- — Z (S) $0
More inspections at Ozark Mountain Tech INC.
View Ozark Mountain Tech INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332813)
More inspections in MO
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340060649.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.