MARSHFIELD, WI —
OSHA Inspection: H & S MANUFACTURING CO., INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of H & S MANUFACTURING CO., INC. in 2608 S. HUME AVENUE, MARSHFIELD, WI 54449 (NAICS 333111). OSHA activity number 340436518.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- H & S MANUFACTURING CO., INC.
- Site address
- 2608 S. HUME AVENUE
- City
- MARSHFIELD
- State
- WI
- ZIP
- 54449
- Mailing
- P.O. BOX 768, MARSHFIELD, WI 54449
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333111
- Employees
- 110
- Ownership type
- A
Citations
8 citations on file for this inspection.
1910.23 C01
- Issued
- Aug 18, 2015
- Abate by
- Sep 9, 2015
- Penalty
- Initial $6,000 · Current $3,600 Reduced
General-duty citation text
29 CFR 1910.23(c)(1): Every open-sided floor or platform 4 feet or more above adjacent floor or ground level shall be guarded by a standard railing (or the equivalent as specified in paragraph (e)(3) of this section) on all open sides except where there is entrance to a ramp, stairway, or fixed ladder: On or about March 2, 2015, employee(s) were exposed to fall hazards while welding on manure spreaders with open sides at heights greater than four feet above the floor.
Recent events (2)
- — I (S) $3600
- — Z (S) $6000
1910.184 E01
- Issued
- Aug 18, 2015
- Abate by
- Sep 9, 2015
- Penalty
- Initial $4,000 · Current $2,400 Reduced
General-duty citation text
29 CFR 1910.184(e)(1): Alloy steel chain slings did not have permanently affixed durable identification stating size, grade, rated capacity, and reach: On or about March 2, 2015, alloy steel chain slings in the welding department did not have identification of size, grade, capacity, and reach affixed to the slings.
Recent events (2)
- — I (S) $2400
- — Z (S) $4000
1910.184 E04
- Issued
- Aug 18, 2015
- Abate by
- Sep 9, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.184(e)(4): Proof testing. The employer did not ensure that before use, each new, repaired, or reconditioned alloy steel chain sling, including all welded components in the sling assembly, was proof tested in accordance with paragraph 5.2 of the American Society of Testing and Materials Specification A391-65: On or about March 2, 2015, shop-fabricated alloy chain slings had not been proof tested.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.217 B04 I
- Issued
- Aug 18, 2015
- Penalty
- Initial $3,000 · Current $1,800 Reduced
General-duty citation text
29 CFR 1910.217(b)(4)(i): The pedal mechanism was not protected to prevent unintended operation from falling or moving objects or by accidental stepping onto the pedal: On or about March 2, 2015, the pedal mechanism on the Bliss No. 23 (Shop No. 492) full-revolution mechanical punch press was not protected to prevent unintended operation.
Recent events (2)
- — I (S) $1800
- — Z (S) $3000
1910.217 B04 II
- Issued
- Aug 18, 2015
- Abate by
- Sep 1, 2015
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(b)(4)(ii): A pad with a non-slip contact area was not firmly attached to the pedal: On or about March 2, 2015, the pedal mechanism on the Bliss No. 23 (Shop No. 492) full-revolution mechanical punch press was not provided with a non-slip contact area.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.217 D05
- Issued
- Aug 18, 2015
- Penalty
- Initial $5,000 · Current $3,000 Reduced
General-duty citation text
29 CFR 1910.217(d)(5): Opening(s) between the top of punch holder(s) and the face of slide(s) or striking pad(s) on mechanical power press(es) were not safeguarded in accordance with the requirements of 29 CFR 1910.217(c): On or about March 2, 2015, the opening between the top of the punch holder and the face of the slide mechanism on the E.W. Bliss No. 23 (Shop No. 492) was not safeguarded.
Recent events (2)
- — I (S) $3000
- — Z (S) $5000
1910.242 B
- Issued
- Aug 18, 2015
- Abate by
- Sep 1, 2015
- Penalty
- Initial $3,000 · Current $1,800 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning purposes was not reduced to less than 30 p.s.i.: On or about March 2, 2015, compressed air used for cleaning purposes in the welding department was not reduced to less than 30 p.s.i.
Recent events (2)
- — I (S) $1800
- — Z (S) $3000
1910.243 B02
- Issued
- Aug 18, 2015
- Abate by
- Sep 1, 2015
- Penalty
- Initial $3,000 · Current $1,800 Reduced
General-duty citation text
29 CFR 1910.243(b)(2): Hose and hose connections used for conducting compressed air to utilization equipment were not designed for the pressure and service to which they were subjected: On or about March 2, 2015, stainless steel hose clamps used to secure quick release fittings to pneumatic air hoses were not designed for the pressure and service to which they were subjected.
Recent events (2)
- — I (S) $1800
- — Z (S) $3000
More inspections at H & S Manufacturing CO., INC.
View H & S Manufacturing CO., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 333111)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340436518.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.