COLUMBUS, NE —
OSHA Inspection: BECTON, DICKINSON AND COMPANY
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of BECTON, DICKINSON AND COMPANY in 1852 10TH AVENUE, COLUMBUS, NE 68601 (NAICS 339112). OSHA activity number 340528959.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- BECTON, DICKINSON AND COMPANY
- Site address
- 1852 10TH AVENUE
- City
- COLUMBUS
- State
- NE
- ZIP
- 68601
- Mailing
- 1852 10TH AVENUE, COLUMBUS, NE 68601
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 339112
- Employees
- 996
- Ownership type
- A
Citations
1 citation on file for this inspection.
1910.212 A01
- Issued
- Apr 22, 2015
- Abate by
- May 26, 2015
- Penalty
- Initial $7,000 · Current $7,000
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: Worksite located at 1852 10th Avenue, Columbus, NE: The following pieces of equipment in the areas identified below are not equipped with machine guarding to prevent the employees from contacting rotating parts or other injurious movements: a) Latch Machine #9, Conveyor system: An indexing location was not provided with guarding to prevent contact with pinch points. An employee sustained a partial amputation as a result of insufficient guarding at this location. b) Tool Room: MSC Drilling and Milling Machine, serial number 6991. c) Tool Room: Bridgeport Milling Machine, serial number J297073. d) Tool Room: Bridgeport Milling Machine, serial number J198566. e) Tool Room: Bridgeport Milling Machine, serial number HJ315203. f) Tool Room: Milltronics Milling Machine, serial number 12401. g) Tool Room: Milltronics Milling Machine, serial number unknown. h) Tool Room: Milltronics Milling Machine, serial number 8206. i) Tool Room: Bridgeport Milling Machine, serial number J304989. j) Tool Room: Wilton VSG Twenty, serial number not identified on the machine. Abatement certification and abatement documentation is required for this violation. The documentation should include written verification of abatement, applicable measurements or monitoring results, and photographs or videos which you believe will be helpful. The abatement certification sheet is enclosed with the citations.
Recent events (1)
- — Z (S) $7000
More inspections at Becton, Dickinson and Company
View Becton, Dickinson and Company's full OSHA safety record →
More inspections in this industry (NAICS 339112)
More inspections in NE
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340528959.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.