OSHA Inspection: GRAPHIC MANAGEMENT SPECIALTY PRODUCTS, INC.

Issued

Jun 23, 2015

Abate by

Jul 29, 2015

Penalty

Initial $3,060 · Current $1,836 Reduced

General-duty citation text

29 CFR 1910.23(c)(1): Open-sided floors and/or platforms four feet or more above adjacent floor or ground level were not guarded with standard railings (or equivalent):    a)    On or about 4/10/2015, machine #610 had an open sided platform was approximately 43" wide with a drop off of approximately 48".

Issued

Jun 23, 2015

Abate by

Jul 1, 2015

Penalty

Initial $3,060 · Current $1,836 Reduced

General-duty citation text

29 CFR 1910.151(c): Where employees were exposed to injurious corrosive materials, suitable facilities for quick drenching or flushing of the eyes and body were not provided within the work area for immediate emergency use:    a)    On or about 4/10/2015, A corrosive KODAK 400R xLo Plate Replenisher was being used in the plate processor without quick drench or flushing facilities in the Pre Press Room.

Issued

Jun 23, 2015

Abate by

Jul 29, 2015

Penalty

Initial $3,825 · Current $2,295 Reduced

General-duty citation text

29 CFR 1910.303(b)(2): Listed or labeled electrical equipment was not used or installed in accordance with instructions included in the listing or labeling:    a)    On or about 4/10/2015, Pre Press room had electrical junction boxes on the floor that were designed for wall mounting and did not provide a sealed unit for wet areas.

Issued

Jun 23, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(g)(1)(vii)(B): The employer did not ensure that outdoor electrical equipment was protected from accidental contact by vehicular traffic.   a)    On or about 4/10/2015, Damaged electrical box had exposed conduit with wiring in it that tested positive for power on the outside loading dock wall outside of door #11. Power had been turned off to damaged conduit outside of door #8.

Issued

Jun 23, 2015

Abate by

Jul 8, 2015

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.303(g)(1): Sufficient access and working space was not provided and maintained about all electric equipment (operating at 600 volts, nominal, or less to ground) to permit ready and safe operation and maintenance of such equipment:  a)    On or about 4/10/2015, working space was not provided in front of electrical circuit breaker boxes located on the mezzanine above the Pre Press room.

Issued

Jun 23, 2015

Abate by

Oct 6, 2015

Penalty

Initial $10,800 · Current $6,480 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    a)    On or about 4/10/2015, pizza label cutting table had multiple pinch and amputation points.    b)    On or about 4/10/2015, jogger table had exposed nip points on aisle side.    c)    On or about 4/10/2015, Machine #610 needed a nip guard for the emboss rolls and packer finger tray guard.    d)    On or about 4/10/2015, Machine #614 needed a nip guard for the emboss rolls and packer finger tray guard.    e)    On or about 4/10/2015, Bretting machine #603 needed star wheel guard put back in place.    f)     On or about 4/10/2015, Scalloper #14 needed a better table guard.    g)    On or about 4/10/2015, Scalloper #8 needed a better side guard to prevent reach over.    GRAPHIC MANAGEMENT SPECIALTY PRODUCTS, INC WAS PREVIOUSLY CITED FOR A VIOLATION OF THIS OCCUPATIONAL SAFETY AND HEALTH STANDARD OR ITS EQUIVALENT 1910.212(A)(1) WHICH WAS CONTAINEDIN OSHA INSPECTION NUMBER 869183, CITATION NUMBER 01, ITEM NUMBER 002, AND WAS AFFIRMED AS A FINAL ORDER ON 3/1/2013, WITH RESPECT TO A WORKPLACE AT 139 EVERGREEN ROAD, OCONTO, WISCONSIN 54153.