CRANBURY, NJ —
OSHA Inspection: LEGACY CONVERTING INC.
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of LEGACY CONVERTING INC. in 3 SECURITY DRIVE, SUITE 301, CRANBURY, NJ 08512 (NAICS 322299). OSHA activity number 340633460.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- LEGACY CONVERTING INC.
- Site address
- 3 SECURITY DRIVE, SUITE 301
- City
- CRANBURY
- State
- NJ
- ZIP
- 08512
- Mailing
- 3 SECURITY DRIVE, SUITE 301, CRANBURY, NJ 08512
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 322299
- Employees
- 22
- Ownership type
- A
Citations
4 citations on file for this inspection.
1910.147 C01
- Issued
- Nov 12, 2015
- Abate by
- Dec 9, 2015
- Penalty
- Initial $2,400 · Current $1,560 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): 29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure and employee training to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, start up or release of stored energy could occur and cause injury, the machine or equipment would be isolated, and rendered inoperative in accordance with 29 CFR 1910.147(c)(4): a) Legacy Converting, Cranbury, NJ- The employer did not establish a program consisting of an energy control procedures and employee training to ensure that before any employee performed any servicing or maintenance on a machines such as but not limited to the Omet Machine, Mutli Pack Machine. Observed on or about on 5/15/2015
Recent events (2)
- — I (S) $1560
- — Z (S) $2400
1910.212 A01
- Issued
- Nov 12, 2015
- Abate by
- Dec 9, 2015
- Penalty
- Initial $2,400 · Current $1,560 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): Machine guarding was not provided to protect operator(s) and other employees from hazards created by in-going nip points, rotating parts, and/or flying chips and sparks: a) The Perini and Elsner machines have no guards exposing the employees to moving parts and amputations hazards. b) The Beck machine, Omet and Cameron 18 have exposed belts and chains exposing the employees to caught on hazards. Observed in or about on 5/15/2015
Recent events (2)
- — I (S) $1560
- — Z (S) $2400
1910.303 G01
- Issued
- Nov 12, 2015
- Abate by
- Dec 9, 2015
- Penalty
- Initial $2,400 · Current $1,560 Reduced
General-duty citation text
29 CFR 1910.303(g)(1): Sufficient access and working space shall be provided and maintained about all electric equipment to permit ready and safe operation and maintenance of such equipment. a) Legacy Converting . Inc., Cranbury, NJ/ Electrical Entry of the warehouse- Electrical panel boxes rated 600 volts or less were blocked by a microwave left for used by the the employees at the facility and a minimum of 30 inches of space was not maintained. b)Legacy Converting . Inc., Cranbury, NJ/North east region near the back emergency exit-The Electrical Panel boxes rated 600 volts or less were blocked by storage materials. Observed on or about 05/15/2015
Recent events (2)
- — I (S) $1560
- — Z (S) $2400
1910.305 G02 III
- Issued
- Nov 12, 2015
- Abate by
- Dec 9, 2015
- Penalty
- Initial $2,400 · Current $1,560 Reduced
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords and cables was not connected to devices and fittings so that the strain relief is provided that will prevent pull from being directly transmitted to joints or terminal screws. (A) Legacy Converting Inc./ Adjacent to the Cameron 18 Machine- Flexible cords and cables were not provided strain relief as required. Observed on or about on 05/15/2015
Recent events (2)
- — I (S) $1560
- — Z (S) $2400
More inspections at Legacy Converting INC.
View Legacy Converting INC.'s full OSHA safety record →
More inspections in this industry (NAICS 322299)
More inspections in NJ
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 340633460.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.