LEBANON, OH —
OSHA Inspection: VISTECH MANUFACTURING SOLUTIONS, LLC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of VISTECH MANUFACTURING SOLUTIONS, LLC. in 265 S. WEST ST, LEBANON, OH 45036 (NAICS 336360). OSHA activity number 341060861.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- VISTECH MANUFACTURING SOLUTIONS, LLC.
- Site address
- 265 S. WEST ST
- City
- LEBANON
- State
- OH
- ZIP
- 45036
- Mailing
- 265 S. WEST ST, LEBANON, OH 45036
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336360
- Employees
- 165
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.147 C04 II B
- Issued
- Jan 15, 2016
- Abate by
- Mar 4, 2016
- Penalty
- Initial $6,930 · Current $6,930
General-duty citation text
29 CFR 1910.147(c)(4)(ii)(B): Specific procedural steps for shutting down, isolating, blocking and securing machines or equipment to control hazardous energy; a) The employer did not develop machine specific procedures for the isolation of equipment with multiple energy sources including but not limited to electrical, hydraulic, air and gravity, in that on or about November 17, 2015 while installing dies into Press 40 the ram came down onto the operators arm and hand.
Recent events (1)
- — Z (S) $6930
1910.147 C07 I A
- Issued
- Jan 15, 2016
- Abate by
- Mar 4, 2016
- Penalty
- Initial $6,930 · Current $6,930
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee shall receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control. a) The employer did not train the employees who install dies into press 40, in the recognition of equipment with multiple energy sources including but not limited to, electrical, hydraulic , air and gravity.
Recent events (1)
- — Z (S) $6930
1910.147 D
- Issued
- Jan 15, 2016
- Abate by
- Mar 4, 2016
- Penalty
- Initial $6,930 · Current $6,930
General-duty citation text
29 CFR 1910.147(d): Application of control. The established procedures for the application of energy control (the lockout or tagout procedures) shall cover the following elements and actions and shall be done in the following sequence: a) Employees who performed servicing and/or maintenance on and around the 40 Press were not required to: (1) Physically locate and operate the electrical disconnect in such a manner as to isolate the machine or equipment from the energy source. In that on or about November 17, 2015 while installing dies into the 40 Press the upper ram came down and onto the operators arm and hand. (2) Affix lockout or tagout devices to the electrical disconnect
Recent events (1)
- — Z (S) $6930
More inspections at Vistech Manufacturing Solutions, LLC.
View Vistech Manufacturing Solutions, LLC.'s full OSHA safety record →
More inspections in this industry (NAICS 336360)
More inspections in OH
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341060861.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.