PIPE CREEK, TX —
OSHA Inspection: COACHWORKS, L.L.C.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of COACHWORKS, L.L.C. in 10498 STATE HWY. 16 S, PIPE CREEK, TX 78063 (NAICS 336213). OSHA activity number 341071595.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Coachworks, L.L.C. — free
Get an email when a new federal OSHA severe-injury report for Coachworks, L.L.C. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- COACHWORKS, L.L.C.
- Site address
- 10498 STATE HWY. 16 S
- City
- PIPE CREEK
- State
- TX
- ZIP
- 78063
- Mailing
- 10498 STATE HWY. 16 S, PIPE CREEK, TX 78063
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 336213
- Employees
- 16
- Ownership type
- A
Citations
8 citations on file for this inspection.
1910.147 C01
- Issued
- Jan 14, 2016
- Abate by
- Feb 3, 2016
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of an energy control procedure, employee training and periodic inspections to ensure that before any employee performed any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: (a) Shop area, table saw #1: On or about November 19, 2015, and at times prior thereto, employees were exposed to hazards associated with unexpected startup while replacing the cutting blade on the table saw. (b) Shop area, table saw #2: On or about November 19, 2015, and at times prior thereto, employees were exposed to hazards associated with unexpected startup while replacing the cutting blade on the table saw.
Recent events (2)
- — I (S) $960
- — Z (S) $1600
1910.212 A03 II
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Points of operation of machinery were not guarded to prevent employees from having any part of their body in the danger zones during operating cycles: In the welding area, west: On or about November 19, 2015, and at times prior thereto, employees were exposed to hazards being struck by flying projectiles and rotating parts when operating a Jet Equipment and Tools drill press without a chip guard.
Recent events (2)
- — I (S) $960
- — Z (S) $1600
1910.212 B
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.212(b): Anchoring fixed machinery. Machines designed for a fixed location shall were not securely anchored to prevent walking or moving: In the welding area, west: On or about November 19, 2015, and at times prior thereto, employees were exposed to hazards being struck by a falling Jet Equipment and Tools drill press without being anchored to the floor.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 D01
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.213(d)(1): Circular handfed crosscut table saw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: (a) Shop area, table saw #1: On or about November 19, 2015, and at times prior thereto, employees were exposed to a caught by hazard, while using a table saw that did not have a guard to protect the employees from the exposed cutting blade. (b) Shop area, table saw #2: On or about November 19, 2015, and at times prior thereto, employees were exposed to a caught by hazard while using a table saw that did not have a guard to protect the employees from the exposed cutting blade.
Recent events (2)
- — I (S) $960
- — Z (S) $1600
1910.215 B09
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch: In the welding area, west: On or about November 19, 2015, and at times prior thereto, employees were exposed to hazards being struck by flying projectiles, while using a bench grinder that did not have a tongue guard to protect the employee from getting struck by a part caught between the rotating wheel and the grinder opening.
Recent events (2)
- — I (S) $720
- — Z (S) $1200
1910.242 B
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $1,200 · Current $720 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning purposes was not reduced to less than 30 p.s.i.: In the welding area, west: On or about November 19, 2015, and at times prior thereto, employees were exposed to the hazard of being struck by flying projectiles, while using compressed air at pressures greater than 30 p.s.i. to remove debris and cool off metal from the work table.
Recent events (2)
- — I (S) $720
- — Z (S) $1200
1910.243 C01
- Issued
- Jan 14, 2016
- Abate by
- Jan 21, 2016
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.243(c)(1): General requirements. Abrasive wheels were not used only on machine provided with safety guards as defined in paragraph (c)(1) through (4) of this section: In the welding area, west: On or about November 19, 2015, and at times prior thereto, employees were exposed to the hazard of being struck by flying projectiles, while using a DeWalt Angle Grinder without a guard to grind before and after welding.
Recent events (2)
- — I (S) $960
- — Z (S) $1600
1910.305 G01 IV A
- Issued
- Jan 14, 2016
- Abate by
- Feb 4, 2016
- Penalty
- Initial $1,600 · Current $960 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv)(A): Flexible cords and/or cables were used as a substitute for the fixed wiring of a structure: (a-e) In the bay coach areas 1-5, north: On or about November 19, 2015, and at times prior thereto, employees were exposed to an electrical hazard, while using portable electrical hand tools that were connected to an extension cord directly attached into the 120 volt electrical box.
Recent events (2)
- — I (S) $960
- — Z (S) $1600
More inspections in this industry (NAICS 336213)
Mar 24, 2026
Forest River INC. · ORLAND, IN
Feb 13, 2026
NEW Horizons RV Corp · JUNCTION CITY, KS
Jan 7, 2026
Thor Motor Coach, INC. · ELKHART, IN
Dec 19, 2025
317742881 - Marathon Coach INC · COBURG, OR
Jun 20, 2025
Thor Motor Coach, INC. · WAKARUSA, IN
More inspections in TX
Jul 17, 2026
Cornelius Nurseries, INC. · RICHMOND, TX
Jul 17, 2026
Holloway Houston, INC. · HOUSTON, TX
Jul 17, 2026
Voluntary Purchasing Groups, INC. · BONHAM, TX
Jul 16, 2026
Rnwbl · SNYDER, TX
Jul 16, 2026
United Rentals, INC. · WICHITA FALLS, TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341071595.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.