WAUSAU, WI —
OSHA Inspection: KOLBE & KOLBE MILLWORK CO., INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of KOLBE & KOLBE MILLWORK CO., INC. in 1323 S. 11TH AVE., WAUSAU, WI 54401 (NAICS 321911). OSHA activity number 341125623.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- KOLBE & KOLBE MILLWORK CO., INC.
- Site address
- 1323 S. 11TH AVE.
- City
- WAUSAU
- State
- WI
- ZIP
- 54401
- Mailing
- 1323 S. 11TH AVE., WAUSAU, WI 54401
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321911
- Employees
- 950
- Ownership type
- A
Citations
9 citations on file for this inspection.
1910.147 C06 I
- Issued
- Feb 17, 2016
- Abate by
- Apr 23, 2016
- Penalty
- Initial $4,250 · Current $2,550 Reduced
General-duty citation text
29 CFR 1910.147(c)(6)(i): The employer did not conduct a periodic inspection of the energy control procedure at least annually to ensure that the procedure and the requirement of this standard were being followed: a) On or about 12/16/2015, the employer was not conducting the required periodic inspection of their energy control program as outlined in their Hazardous Energy Control Program dated 07-08-2014.
Recent events (2)
- — I (S) $2550
- — Z (S) $4250
1910.213 C02
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $4,250 · Current $2,550 Reduced
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator: a) On or about 12/16/2015, DELTA UNISAW, 10" Tilting Arbor Saw, in the maintenance shop was not equipped with a spreader. I.D. Number 1531
Recent events (2)
- — I (S) $2550
- — Z (S) $4250
1910.213 C03
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: a) On or about 12/16/2015, DELTA UNISAW, 10" Tilting Arbor Saw, in the maintenance shop was not equipped with non kickback fingers. I.D. Number 1531
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 P04
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(p)(4): Belt sanding machinery was not provided with a guard at each nip point where the sanding belt ran onto a pulley, to prevent the operator's hands or fingers from coming into contact with nip points: a) On or about 12/16/2015,Vertical belt sander guards were not fully enclosing to prevent contact with belt nip points on Sander #44, Marathon motor ID 1744.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 R01
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(r)(1): Feed rolls of roll type glue spreader(s) were not guarded by a semicylindrical guard: a) On or about 12/16/2015, BLACK BROS #1 glue spreader needed better guarding on the rolls.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 C04 II
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $4,250 · Current $2,550 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(ii): The unused keyway(s) of projecting shaft end(s) were not filled up or covered: a) On or about 12/16/2015, BLACK BROS #1 glue spreader needed better guarding on the exposed shaft ends.
Recent events (2)
- — I (S) $2550
- — Z (S) $4250
1910.219 D01
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(d)(1): Pulley(s) with part(s) seven feet or less from the floor or work platform were not guarded in accordance with the requirements specified in 29 CFR 1910.219(m) and (o): a) On or about 12/16/2015, BLACK BROS #1 glue spreader needed better guarding on the pulleys and belts that were not back guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 E03 I
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(3)(i): Vertical or inclined belt(s) were not enclosed by guard(s) conforming to the requirements specified at 29 CFR 1910.219(m) and (o): a) On or about 12/16/2015, BLACK BROS #1 glue spreader needed better guarding on the pulleys and belts that were not back guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 F03
- Issued
- Feb 17, 2016
- Abate by
- Mar 23, 2016
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(f)(3): Sprocket wheels and chains which were seven -7 feet or less above floors or platforms were not enclosed: a) On or about 12/16/2015, BLACK BROS #1 glue spreader needed better guarding on the chains and sprockets that were not back guarded.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at Kolbe & Kolbe Millwork CO., INC.
View Kolbe & Kolbe Millwork CO., INC.'s full OSHA safety record →
More inspections in this industry (NAICS 321911)
More inspections in WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 341125623.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.