OSHA Inspection: RIVERSTONE SANCTUARY - CBD- INC.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $2,423 · Current $1,359 Reduced

General-duty citation text

29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms or service rooms were not kept clean and orderly or in a sanitary condition.      On or about September 7, 2016, at the shop of above addressed jobsite, employees worked in a space with Class II combustible dust accumulation exceeding 1/8-inch in 32.95% of the floor and overhead beam areas.

Issued

Oct 19, 2016

Penalty

Initial $1,545 · Current $866 Reduced

General-duty citation text

29 CFR 1910.212(b): Machine(s) designed for fixed location(s) were not securely anchored to prevent walking or moving:    On or about September 7, 2016, at the shop of the above addressed jobsite, an employee was exposed to a struck by hazard while working with a saw (i.e. Ridgid R4112, 120 V, 60 Hertz) that was not anchored.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $3,029 · Current $1,699 Reduced

General-duty citation text

29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut    On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a caught by hazard while working with a table saw (i.e. Delta Unisaw) that lacked a guard over the blade.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator:  On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a struck by hazard while working with a table saw (i.e. Delta Unisaw) that lacked a spreader.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator:   On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a struck by hazard while working with a table saw (i.e. Delta Unisaw) that lacked non kickback fingers or dogs.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(d)(1): Circular handfed crosscut table saw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut:  a.  On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a caught by hazard while working with a table saw (i.e. Holzner #1243) whose guard was not adjusted properly to cover the portion of blade above the table and that above material being cut.  b.  On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a caught by hazard while working with a table saw (i.e. Delta Unisaw) that lacked a guard over the blade.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $2,423 · Current $1,359 Reduced

General-duty citation text

29 CFR 1910.213(l)(2): Boring bits where not provided with guards that would enclose all portions of the bit and chuck above the material being worked:       On or about September 7, 2016, at the shop of the above addressed jobsite, employees were exposed to a caught by hazard while working with a dual-line boring machine (i.e. Conquest Ind.) that had a portion of its wood guard broken.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $2,423 · Current $1,359 Reduced

General-duty citation text

29 CFR 1910.215(a)(1): Abrasive wheel(s) used on grinding machinery were not used with safety guard(s):      On or about September 7, 2016, at the shop of above addressed worksite, employees were exposed to a struck by hazard while working with a bench grinder (i.e. no info available) that lacked a safety guard on both sides.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(a)(4): Work rest(s) on grinding machinery were not adjusted closely to the wheel with a maximum opening of one eighth inch:  On or about September 7, 2016, at the shop of above addressed worksite, employees were exposed to a struck by hazard while working with a bench grinder (i.e. no info available) that lacked a workrest on both sides.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.215(b)(9): The distance between the abrasive wheel periphery(s) and the adjustable tongue or the end of the safety guard peripheral member at the top exceeded one fourth inch:   On or about September 7, 2016, at the shop of above addressed worksite, employees were exposed to a struck by hazard while working with a bench grinder (i.e. no info available) that lacked a tongue guard on both sides.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $2,423 · Current $1,359 Reduced

General-duty citation text

29 CFR 1910.307(c): Equipment, wiring methods, and installations of equipment in hazardous (classified) locations were not intrinsically safe, approved for the hazardous (classified) location, or safe for the hazardous (classified) location:      On or about September 7, 2016, at the shop of above addressed jobsite, a vacuum cleaner (i.e. Ridgid ShopVac) was used to collect wood dust, which was not intrinsically safe, approved for a Class II, Division 2 location or safe for a Class II Division 2 location.

Issued

Oct 19, 2016

Abate by

Nov 2, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.178(l)(1)(i): The employer did not ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l):  On or about September 7, 2016 at the above addressed jobsite, employees operated a powered industrial truck (i.e. Hyster, Model #560FT, Serial # F187VD2948C) without being trained and evaluated.

Issued

Oct 19, 2016

Abate by

Oct 26, 2016

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.305(b)(2): Each outlet box in completed installations did not have a cover, faceplate, or fixture canopy:   On or about September 7, 2016, at the shop area of above addressed jobsite, an electrical outlet lacked a cover plate, exposing employees to a fire hazard.