MINEOLA, NY —
OSHA Inspection: D. REIS FURNITURE MANUFACTURING CORP.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of D. REIS FURNITURE MANUFACTURING CORP. in 327 SAGAMORE AVENUE, MINEOLA, NY 11501 (NAICS 337122). OSHA activity number 342240041.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- D. REIS FURNITURE MANUFACTURING CORP.
- Site address
- 327 SAGAMORE AVENUE
- City
- MINEOLA
- State
- NY
- ZIP
- 11501
- Mailing
- 327 SAGAMORE AVENUE, MINEOLA, NY 11501
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337122
- Employees
- 50
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 C01
- Issued
- Sep 14, 2017
- Abate by
- Nov 1, 2017
- Penalty
- Initial $8,873 · Current $6,652 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative. Worksite: Employees are required to provide repair and maintenance on equipment such as, but not limited to an Otto Martin Maschinebau T26 Router , Otto Martin Maschinebau T72 Table Saw , and a Sicma DT530 Plainer. The employer did not provide the employees with a Lockout/Tagout program; on or about 4/11/17. Note: The employer is required to submit abatement certification for this item in accordance with 29 CFR 1903.19.
Recent events (2)
- — I (S) $6652
- — Z (S) $8873
1910.147 C04 I
- Issued
- Sep 14, 2017
- Abate by
- Nov 1, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section. a) Worksite: Employees are required to provide repair and maintenance on equipment such as, but not limited to Otto Martin Maschinebau T26 Router , Otto Martin Maschinebau T72 Table Saw , and a Sicma DT530 Plainer. The employer did not develop, document and utilize Lockout/Tagout procedures to control hazardous energy; on or about 4/11/17. Note: The employer is required to submit abatement certification for this item in accordance with 29 CFR 1903.19.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C05 I
- Issued
- Sep 14, 2017
- Abate by
- Nov 1, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(5)(i): Locks, tags, chains, wedges, key blocks, adapter pins, self-locking fasteners, or other hardware were not provided by the employer for isolating, securing or blocking of machines or equipment from energy sources: a) Worksite: Employees are required to provide repair and maintenance on equipment such as, but not limited to an Otto Martin Maschinebau T26 Router , Otto Martin Maschinebau T72 Table Saw , and a Sicma DT530 Plainer. The employer did not provide the employees with hardware; on or about 4/11/17. Note: The employer is required to submit abatement certification for this item in accordance with 29 CFR 1903.19.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 C07 I B
- Issued
- Sep 14, 2017
- Abate by
- Nov 1, 2017
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i)(B): Each affected employee shall be instructed in the purpose and use of the energy control procedure. a) Worksite: Employees are required to provide repair and maintenance on equipment such as, but not limited to an Otto Martin Maschinebau T26 Router , Otto Martin Maschinebau T72 Table Saw , and a Sicma DT530 Plainer. The employees were not provided with Lockout/Tagout training; on or about 4/11/17. Note: The employer is required to submit abatement certification for this item in accordance with 29 CFR 1903.19.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 C01
- Issued
- Sep 14, 2017
- Abate by
- Sep 20, 2017
- Penalty
- Initial $8,873 · Current $6,652 Reduced
General-duty citation text
29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut: a) Workplace - Employees operating Machines such as but not limited to an Otto Martin Maschinenbau table saw, were not protected from the moving 12inch blade; on or about 4/5/17. b) Workplace - Employees operating Machines such as but not limited to an Otto Martin Maschinenbau table saw, were not protected from the moving 12inch blade; on or about 4/11/17. Note: The employer is required to submit abatement certification for this item in accordance with 29 CFR 1903.19.
Recent events (2)
- — I (S) $6652
- — Z (S) $8873
1904.39 A02
- Issued
- Sep 14, 2017
- Penalty
- Initial $1,000 · Current $736 Reduced
General-duty citation text
29 CFR 1904.39(a)(2): The employer failed to report the in-patient hospitalization of one or more employees or an employee's amputation or an employee's loss of an eye, as a result of a work-related incident. The employer did not report the in-patient hospitalization, amputation, or loss of an eye to OSHA within twenty-four (24) hours. a) Worksite, 2 Mallard Ave., Manhasset NY - An employee partially amputated three fingers while using an Otto Martin Maschinebau T72 Table Saw. The employer failed to report the amputation to OSHA within 24 hours of the incident; on or about 4/5/17. Note: Because abatement of this violation is already documented in the case file, the employer need not submit certification or documentation of abatement for this violation as normally required by CFR 1903.19.
Recent events (2)
- — I (O) $736
- — Z (O) $1000
More inspections at D. Reis Furniture Manufacturing Corp.
View D. Reis Furniture Manufacturing Corp.'s full OSHA safety record →
More inspections in this industry (NAICS 337122)
More inspections in NY
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342240041.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.