FAIRMONT, WV —
OSHA Inspection: MOUNTAINEER CABINET COMPANY, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MOUNTAINEER CABINET COMPANY, INC. in 1917/1918 LOCUST AVENUE, FAIRMONT, WV 26554 (NAICS 337110). OSHA activity number 342998895.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MOUNTAINEER CABINET COMPANY, INC.
- Site address
- 1917/1918 LOCUST AVENUE
- City
- FAIRMONT
- State
- WV
- ZIP
- 26554
- Mailing
- 1917 LOCUST AVENUE, FAIRMONT, WV 26554
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 337110
- Employees
- 26
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.147 D04 I
- Issued
- Apr 12, 2018
- Abate by
- May 1, 2018
- Penalty
- Initial $6,467 · Current $3,556 Reduced
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: (a) Rough Mill: On or about February 27, 2018 and times prior, an employee performs servicing and maintenance, such as changing the blade on the 3 phase 240V American Saw Mill Machinery Company bandsaw (Serial No. 431184), without affixing a lock to the energy insolating device.
Recent events (2)
- — I (O) $3556
- — Z (S) $6467
1910.213 C02
- Issued
- Apr 12, 2018
- Abate by
- May 1, 2018
- Penalty
- Initial $7,760 · Current $4,268 Reduced
General-duty citation text
29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator: (a) Rough Mill, Drawer Area: On or about February 27, 2018 and times prior, an employee would use the Darra James table saw to rip wooden boards. The saw was not equipped with a spreader.
Recent events (2)
- — I (S) $4268
- — Z (S) $7760
1910.213 C03
- Issued
- Apr 12, 2018
- Abate by
- May 1, 2018
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator: (a) Rough Mill, Drawer Area: On or about February 27, 2018 and times prior, an employee would use the Darra James table saw to rip wooden boards. The saw was not equipped with an anti-kickback device.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 H01
- Issued
- Apr 12, 2018
- Abate by
- May 1, 2018
- Penalty
- Initial $5,174 · Current $2,846 Reduced
General-duty citation text
29 CFR 1910.213(h)(1): The sides of the lower exposed portion of the blade of radial saw(s) were not guarded to the full diameter of the blade by a device that automatically adjusted itself to the thickness of the stock and remained in contact with the material. (a) Drawer Area: On or about March 4, 2018 and times prior, an employees would cut material using the DeWalt 7790 radial saw that had a side guard that did not guard the full diameter of the blade while in operation. (b) Rough Mill: On or about February 13, 2018 and times prior, an employee would cut material using the DeWalt 7730 radial saw that had a side guard that did not guard the full diameter of the blade while in operation. (a) Assembly Area: On or about December 4, 2018 and times prior, an employee would cut material using the DeWalt 7770 radial saw that had a side guard that did not guard the full diameter of the blade while in operation.
Recent events (2)
- — I (S) $2846
- — Z (S) $5174
1910.213 I01
- Issued
- Apr 12, 2018
- Abate by
- May 1, 2018
- Penalty
- Initial $7,760 · Current $4,268 Reduced
General-duty citation text
29 CFR 1910.213(i)(1): Non-working portion(s) of the blade of bandsaw(s) were not enclosed or guarded: (a) Assembly: On or about March 6, 2018 and times prior, employees used the Gullmeyer & Livingston Company 'Union' vertical bandsaw to cut approximately 5/8" pieces of material with approximately 4 5/8" of exposed blade.
Recent events (2)
- — I (S) $4268
- — Z (S) $7760
More inspections at Mountaineer Cabinet Company, INC.
View Mountaineer Cabinet Company, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 337110)
More inspections in WV
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 342998895.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.