TYLER, TX —
OSHA Inspection: CENTRAL PALLET, LLC
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of CENTRAL PALLET, LLC in 1352 E. NORTHEAST LOOP 323, TYLER, TX 75708 (NAICS 321920). OSHA activity number 343127726.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- CENTRAL PALLET, LLC
- Site address
- 1352 E. NORTHEAST LOOP 323
- City
- TYLER
- State
- TX
- ZIP
- 75708
- Mailing
- 4929 BARCLAY DRIVE, TYLER, TX 75703
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 321920
- Employees
- 20
- Ownership type
- A
Citations
3 citations on file for this inspection.
1910.28 B01 I A
- Issued
- Aug 8, 2018
- Abate by
- Oct 5, 2018
- Penalty
- Initial $2,217 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.28(b)(1)(i)(A): The employer did not ensure each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by a guardrail system. This violation was discovered on or about May 1, 2018; where employees in the notch cutting and chop areas were exposed to a fall of approximately 5 feet 8 inches.
Recent events (2)
- — I (S) $1200
- — Z (S) $2217
1910.147 C01
- Issued
- Aug 8, 2018
- Abate by
- Oct 5, 2018
- Penalty
- Initial $2,217 · Current $1,200 Reduced
General-duty citation text
29 CFR 1910.147(c)(1): The employer did not establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative: This violation was discovered on or about May 1, 2018, when the employer did not establish a program consisting of energy control procedures to include but not limited to employee training and periodic inspections. Employees were exposed to caught-in and/or amputation hazards.
Recent events (2)
- — I (S) $1200
- — Z (S) $2217
1910.212 A01
- Issued
- Aug 8, 2018
- Abate by
- Oct 5, 2018
- Penalty
- Initial $5,174 · Current $3,000 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): The employer did not ensure that at least one or more methods of machine guarding was provided to protect the operators and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. This violation was discovered on or about May 1, 2018; where employees operating the 8' Morgan Resaw were exposed to amputation hazards.
Recent events (2)
- — I (S) $3000
- — Z (S) $5174
More inspections at Central Pallet, LLC
View Central Pallet, LLC's full OSHA safety record →
More inspections in this industry (NAICS 321920)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343127726.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.