CHETEK, WI —
OSHA Inspection: CORE PRODUCTS INTERNATIONAL, INC.
Referral inspection · Safety discipline
At a glance
On , OSHA opened a referral safety inspection of CORE PRODUCTS INTERNATIONAL, INC. in 1505 PARKER DRIVE, CHETEK, WI 54728 (NAICS 339113). OSHA activity number 343788501.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Core Products International, INC. — free
Get an email when a new federal OSHA severe-injury report for Core Products International, INC. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- CORE PRODUCTS INTERNATIONAL, INC.
- Site address
- 1505 PARKER DRIVE
- City
- CHETEK
- State
- WI
- ZIP
- 54728
- Mailing
- 808 PROSPECT AVENUE, OSCEOLA, WI 54020
What kind of inspection was it?
- Inspection type
- Referral (C)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 339113
- Employees
- 77
- Ownership type
- A
Citations
10 citations on file for this inspection.
1910.147 C04 I
- Issued
- May 6, 2019
- Abate by
- Aug 23, 2019
- Penalty
- Initial $11,934 · Current $8,354 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: (a) Cutting department; Energy isolation procedures were not documented.
Recent events (2)
- — I (S) $8353.8
- — Z (S) $11934
1910.147 C07 I A
- Issued
- May 6, 2019
- Abate by
- Aug 23, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control: (a) Cutting department; Authorized level lockout training was not provided for workers who perform lockout covered activities, including but not limited to; setup and blade change operations on strip cutters.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 D03
- Issued
- May 6, 2019
- Abate by
- Aug 23, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(3): All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): (a) Cutting department; Electrical and pneumatic sources of energy were not isolated on strip cutting machines during setup and roll changing operations.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.147 D04 I
- Issued
- May 6, 2019
- Abate by
- Aug 23, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: (a) Cutting department; Lockout devices are not affixed to isolation points for electrical and pneumatic energy on strip cutting machines during setup and roll changing operations. (b) Cutting department; Lockout devices are not affixed to isolation points for pneumatic energy on strip cutting machines during blade change operations.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.212 A01
- Issued
- May 6, 2019
- Abate by
- May 20, 2019
- Penalty
- Initial $11,934 · Current $8,354 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) Cutting department; Guarding was not provided for ingoing nip points between powered feed rollers on the infeed side of strip cutting machines, including but not limited to; Asset. Numbers 655, 931, and 932. (b) Cutting department; Guarding was not provided for pinch points between the knife holder and upper frame on the infeed side of strip cutting machines, including but not limited to; Asset. Numbers 655, 933, 931, and 932.
Recent events (2)
- — I (S) $8353.8
- — Z (S) $11934
1910.212 A03 II
- Issued
- May 6, 2019
- Abate by
- May 20, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.212(a)(3)(ii): Point(s) of operation of machinery were not guarded to prevent employee(s) from having any part of their body in the danger zone(s) during operating cycle(s): (a) Cutting department; Point of operation guarding was not provided for the cutting knife on strip cutting machines, including but not limited to; Asset. Numbers 655, 933, 931, and 932. On or about February 5, 2019, An amputation injury occurred in the point of operation, on the outfeed side of a TRC 1000 VS strip cutting machine.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.303 G02 I
- Issued
- May 6, 2019
- Abate by
- May 20, 2019
- Penalty
- Initial $5,115 · Current $3,581 Reduced
General-duty citation text
29 CFR 1910.303(g)(2)(i): Live parts of electric equipment operating at 50 volts or more were not guarded against accidental contact by approved cabinets or other forms of approved enclosures, or other means listed under this provision: (a) Cutting department; Protection was not provided for energized 120 volt conductors on a TRC brand VS 1000 strip cutter (Asset. 931) by enclosure or elevation.
Recent events (2)
- — I (S) $3580.5
- — Z (S) $5115
1904.32 B02 II
- Issued
- May 6, 2019
- Abate by
- May 20, 2019
- Penalty
- Initial $1,706 · Current $1,195 Reduced
General-duty citation text
29 CFR 1904.32(b)(2)(ii): The employer did not complete on the annual summary, the calendar year covered, the company's name, establishment name, establishment address, annual average number of employees covered by the OSHA 300 Log, and the total hours worked by all employees covered by the OSHA 300 Log: (a) Throughout the Chetek, WI facility; On February 14, 2019, The employer's annual summary of injuries and illnesses (OSHA Form 300A) for calendar year 2018 was not completely filled out.
Recent events (2)
- — I (O) $1194.9
- — Z (O) $1706
1904.40 A
- Issued
- May 6, 2019
- Abate by
- May 20, 2019
- Penalty
- Initial $1,706 · Current $0 Reduced
General-duty citation text
29 CFR 1904.40(a): The employer did not provide an authorized government representative the records within the four business hours: (a) Throughout the Chetek, WI facility; On February 14, 2019, The employer did not provide their injury and illness log (OSHA Form 300) for calendar year 2019.
Recent events (2)
- — I (O) $0
- — Z (O) $1706
1910.1030 C01 I
- Issued
- May 6, 2019
- Abate by
- Aug 23, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.1030(c)(1)(i): The employer having employee(s) with occupational exposure did not establish a written Exposure Control Plan designed to eliminate or minimize employee exposure: (a) Throughout the Chetek, WI facility; On or about February 5, 2019, a written Exposure Control Plan was not developed and implemented before designated employees rendered first aid and cleaned up blood related to an amputation injury that occurred.
Recent events (2)
- — I (O) $0
- — Z (O) $0
More inspections at Core Products International, INC.
Sep 19, 2022
CHETEK, WI
Dec 26, 2019
CHETEK, WI
Feb 13, 2012
CHETEK, WI
Oct 16, 1995
ST PAUL, MN
Dec 2, 1993
ST PAUL, MN
View Core Products International, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 339113)
May 21, 2026
Hollister Incorporated · MT JULIET, TN
May 14, 2026
Rescue 42, INC · CHICO, CA
Apr 21, 2026
Galvion Ballistics LTD. · NEWPORT, VT
Mar 26, 2026
Invotec International INC · JACKSONVILLE, FL
Mar 26, 2026
Stemrad · TAMPA, FL
More inspections in WI
Jul 17, 2026
PTS Contractors, INC. · GREEN BAY, WI
Jul 16, 2026
Miron Construction CO. INC. · WAUSAU, WI
Jul 15, 2026
Wabash National Services, L.P. · ELROY, WI
Jul 15, 2026
Kings Superior Construction LLC · SUSSEX, WI
Jul 15, 2026
Teronomy Builders, INC. · DELAVAN, WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 343788501.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.