CHETEK, WI —
OSHA Inspection: CORE PRODUCTS INTERNATIONAL, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of CORE PRODUCTS INTERNATIONAL, INC. in 1505 PARKER DRIVE, CHETEK, WI 54728 (NAICS 339113). OSHA activity number 344534490.
What this inspection record means
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Watch Core Products International, INC. — free
Get an email when a new federal OSHA severe-injury report for Core Products International, INC. is published. One employer, no account, unsubscribe in one click.
Where did this inspection happen?
- Establishment
- CORE PRODUCTS INTERNATIONAL, INC.
- Site address
- 1505 PARKER DRIVE
- City
- CHETEK
- State
- WI
- ZIP
- 54728
- Mailing
- 1505 PARKER DRIVE, CHETEK, WI 54728
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 339113
- Employees
- 83
- Ownership type
- A
Citations
10 citations on file for this inspection.
1910.212 A01
- Issued
- May 27, 2020
- Abate by
- Jun 10, 2020
- Penalty
- Initial $5,725 · Current $4,007 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) Cutting department; Guarding was not provided for rotating parts and flying chips on 1/3 Hp drill presses. (b) Maintenance shop area; Guarding was not provided for rotating parts and flying chips on a 3/4 Hp drill presses.
Recent events (2)
- — I (S) $4007
- — Z (S) $5725
1910.219 B01
- Issued
- May 27, 2020
- Abate by
- Jun 10, 2020
- Penalty
- Initial $7,634 · Current $5,343 Reduced
General-duty citation text
29 CFR 1910.219(b)(1): Flywheel(s) with parts seven feet or less above floor(s) or platform(s) were not guarded in accordance with the requirements specified in 29 CFR 1910.219(b)(1)(i) through (b)(1)(iv): (a) Various products area; The power transmission flywheel on an Alva F. Allen brand, 2 ton mechanical benchtop punch press (model DEJ14260) was not fully enclosed by guarding.
Recent events (2)
- — I (S) $5343
- — Z (S) $7634
1910.219 E01 I
- Issued
- May 27, 2020
- Abate by
- Jun 10, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.219(e)(1)(i): Horizontal belts which had both runs 42 inches or less from the floor level were not fully enclosed by guards conforming to requirements specified in 29 CFR 1910.219(m) and (o): (a) Various products area; The power transmission belt on an Alva F. Allen brand, 2 ton mechanical benchtop punch press (model DEJ14260) was not fully enclosed by guarding.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.219 C04 I
- Issued
- May 27, 2020
- Abate by
- Jun 10, 2020
- Penalty
- Initial $5,725 · Current $4,007 Reduced
General-duty citation text
29 CFR 1910.219(c)(4)(i): Unguarded projecting shaft end(s) did not present a smooth edge and projected more than one half the diameter of the shaft: (a) Fiber filling area; The ends of eight unguarded protruding shafts were not smooth and projected more than one-half the diameter of the shaft on a Carolina Machinery Company brand fiber filling machine (EF-38-4).
Recent events (2)
- — I (S) $4007
- — Z (S) $5725
1910.305 B01 II
- Issued
- May 27, 2020
- Penalty
- Initial $5,725 · Current $4,007 Reduced
General-duty citation text
29 CFR 1910.305(b)(1)(ii): Unused openings in boxes, cabinets, or fittings were not effectively closed: (a) Cutting department; An unused hole in electrical junction box containing 120 VAC conductors was not closed on a Chen Feng Hydraulic Machinery Company brand, Hydraulic Traveling Head Cutting Press (Model CF-756).
Recent events (2)
- — I (S) $4007
- — Z (S) $5725
1910.147 C07 I A
- Issued
- May 27, 2020
- Abate by
- Jun 17, 2020
- Penalty
- Initial $26,718 · Current $16,030 Reduced
General-duty citation text
29 CFR 1910.147(c)(7)(i)(A): Each authorized employee did not receive training in the recognition of applicable hazardous energy sources, the type and magnitude of the energy available in the workplace, and the methods and means necessary for energy isolation and control: (a) Cutting department; Authorized level lockout training was not provided for workers who perform lockout covered activities of changing blades on Gerber brand, fabric cutting machines. The Core Products International, Inc was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.147(c)(7)(i)(A), which was contained in OSHA inspection number 1378850, citation number 1, item number 1b and was affirmed as a final order on May 22, 2019, with respect to a workplace located at 1505 Parker Drive, Chetek, WI 54728.
Recent events (2)
- — I (R) $16030
- — Z (R) $26718
1910.147 D03
- Issued
- May 27, 2020
- Abate by
- Jun 17, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(3): All energy isolating devices that were needed to control the energy to the machine or equipment were not physically located and operated in such a manner as to isolate the machine or equipment from the energy source(s): (a) Cutting department; Electrical and pneumatic sources of energy were not isolated on Gerber brand, fabric cutting machines during blade changing operations. The Core Products International, Inc was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.147(d)(3), which was contained in OSHA inspection number 1378850, citation number 1, item number 1c and was affirmed as a final order on May 22, 2019, with respect to a workplace located at 1505 Parker Drive, Chetek, WI 54728.
Recent events (2)
- — I (R) $0
- — Z (R) $0
1910.147 D04 I
- Issued
- May 27, 2020
- Abate by
- Jun 17, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.147(d)(4)(i): Lockout or tagout devices were not affixed to each energy isolating device by authorized employees: (a) Cutting department; Lockout locks were not affixed on electrical and pneumatic energy isolation points for Gerber brand, fabric cutting machines during blade changing operations. The Core Products International, Inc was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.147(d)(4)(i), which was contained in OSHA inspection number 1378850, citation number 1, item number 1d and was affirmed as a final order on May 22, 2019, with respect to a workplace located at 1505 Parker Drive, Chetek, WI 54728.
Recent events (2)
- — I (R) $0
- — Z (R) $0
1910.212 A01
- Issued
- May 27, 2020
- Penalty
- Initial $19,085 · Current $11,451 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) Cutting department; Guarding was not provided for pinch points between the knife holder and upper frame on the infeed side of a Sheffield brand strip cutting machine (asset number 1099). The Core Products International, Inc was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.212(a)(1), which was contained in OSHA inspection number 1378850, citation number 1, item number 2a and was affirmed as a final order on May 22, 2019, with respect to a workplace located at 1505 Parker Drive, Chetek, WI 54728
Recent events (2)
- — I (R) $11451
- — Z (R) $19085
1904.40 A
- Issued
- May 27, 2020
- Penalty
- Initial $1,909 · Current $0 Reduced
General-duty citation text
29 CFR 1904.40(a): The employer did not provide an authorized government representative the records within the four business hours: (a) Throughout the facility; The employer did not provide OSHA injury and illnesses Forms 300 and 300A within four hours.
Recent events (2)
- — I (O) $0
- — Z (O) $1909
More inspections at Core Products International, INC.
Sep 19, 2022
CHETEK, WI
Feb 14, 2019
CHETEK, WI
Feb 13, 2012
CHETEK, WI
Oct 16, 1995
ST PAUL, MN
Dec 2, 1993
ST PAUL, MN
View Core Products International, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 339113)
May 21, 2026
Hollister Incorporated · MT JULIET, TN
May 14, 2026
Rescue 42, INC · CHICO, CA
Apr 21, 2026
Galvion Ballistics LTD. · NEWPORT, VT
Mar 26, 2026
Invotec International INC · JACKSONVILLE, FL
Mar 26, 2026
Stemrad · TAMPA, FL
More inspections in WI
Jul 17, 2026
PTS Contractors, INC. · GREEN BAY, WI
Jul 16, 2026
Miron Construction CO. INC. · WAUSAU, WI
Jul 15, 2026
Wabash National Services, L.P. · ELROY, WI
Jul 15, 2026
Kings Superior Construction LLC · SUSSEX, WI
Jul 15, 2026
Teronomy Builders, INC. · DELAVAN, WI
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344534490.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.