LUBBOCK, TX —
OSHA Inspection: MODULE TRUCK SYSTEMS, INC.
Planned inspection · Health discipline
At a glance
On , OSHA opened a planned health inspection of MODULE TRUCK SYSTEMS, INC. in 2010 E. 50TH STREET, LUBBOCK, TX 79404 (NAICS 333111). OSHA activity number 344072673.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MODULE TRUCK SYSTEMS, INC.
- Site address
- 2010 E. 50TH STREET
- City
- LUBBOCK
- State
- TX
- ZIP
- 79404
- Mailing
- P.O. BOX 3910, LUBBOCK, TX 79452
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Health
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 333111
- Employees
- 30
- Ownership type
- A
Citations
5 citations on file for this inspection.
1910.134 E01
- Issued
- Nov 19, 2019
- Abate by
- Dec 16, 2019
- Penalty
- Initial $5,304 · Current $3,182 Reduced
General-duty citation text
29 CFR 1910.134(e)(1): The employer did not provide a medical evaluation to determine the employee's ability to use a respirator, before the employee was fit tested or required to use the respirator in the workplace: At the facility, the employer did not provide medical evaluations for employees required to wear full face respirators while working in the spray paint booth.
Recent events (2)
- — I (S) $3182.4
- — Z (S) $5304
1910.134 F02
- Issued
- Nov 19, 2019
- Abate by
- Dec 16, 2019
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.134(f)(2): Employee(s) using tight-fitting facepiece respirators were not fit tested prior to initial use of the respirator: At the facility, the employer did not provide fit tests for employees who wore tight-fitting full face respirators prior to wearing the respirators.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.178 P01
- Issued
- Nov 19, 2019
- Abate by
- Dec 16, 2019
- Penalty
- Initial $5,304 · Current $3,182 Reduced
General-duty citation text
29 CFR 1910.178(p)(1): Powered industrial truck(s) found to be in need of repair, defective, or in any way unsafe had not been taken out of service until restored to safe operating condition(s): At the facility, employees were exposed to struck-by hazards while operating a defective powered industrial truck that had not been taken out of service.
Recent events (2)
- — I (S) $3182.4
- — Z (S) $5304
1910.254 D09 III
- Issued
- Nov 19, 2019
- Abate by
- Dec 16, 2019
- Penalty
- Initial $3,978 · Current $2,387 Reduced
General-duty citation text
29 CFR 1910.254(d)(9)(iii): Cables with damaged insulation or exposed bare conductors were not replaced: At the facility, employer did not ensure cables on the welding machine were replaced and exposed employees to electrical shock hazards. a) Miller welding machine located on the north end of the welding/manufacturing area. b) Miller welding machine located in section 847. c) Miller welding machine located on the north wall in the maintenance shop at Bay #1
Recent events (2)
- — I (S) $2386.8
- — Z (S) $3978
1910.305 G02 III
- Issued
- Nov 19, 2019
- Abate by
- Dec 16, 2019
- Penalty
- Initial $744 · Current $446 Reduced
General-duty citation text
29 CFR 1910.305(g)(2)(iii): Flexible cords and cables were not connected to devices and fittings so that strain relief was provided that would prevent pull from being directly transmitted to joints or terminal screws: At the facility, employer did not ensure a strain relief was installed on a flexible cord used to supply electric current to equipment. a) Miller welding machine located on the east center wall in the welding/manufacturing area. b) Miller welding machine located in section #825. c) Drill press located in section 831, station 2 in the frame assembly area.
Recent events (2)
- — I (O) $446.4
- — Z (O) $744
More inspections in this industry (NAICS 333111)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344072673.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.