SAN ANTONIO, TX —
OSHA Inspection: C & C SAGE, INC.
Federal Agency inspection · Safety discipline
At a glance
On , OSHA opened a federal Agency safety inspection of C & C SAGE, INC. in 3626 BINZ-ENGLEMAN RD., SAN ANTONIO, TX 78219 (NAICS 327991). OSHA activity number 344131925.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- C & C SAGE, INC.
- Site address
- 3626 BINZ-ENGLEMAN RD.
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78219
- Mailing
- 3626 BINZ-ENGLEMAN RD., SAN ANTONIO, TX 78219
What kind of inspection was it?
- Inspection type
- Federal Agency (M)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 327991
- Employees
- 96
- Ownership type
- A
Citations
5 citations on file for this inspection.
5(a)(1)
- Issued
- Dec 23, 2019
- Abate by
- Jan 6, 2020
- Penalty
- Initial $9,282 · Current $7,425 Reduced
General-duty citation text
OSH ACT of 1970 Section (5)(a)(1): The employer did not furnish employment and a place of employment which were free from recognized hazards that were causing or likely to cause death or serious physical harm to employees in that employees were exposed to an ejection and crushing hazard: Outside in the east lot: On or about July 4, 2019, an employee was exposed to crushing hazards while operating a Nissan 50 forklift, while not utilizing/wearing the required seatbelt.
Recent events (2)
- — I (S) $7425
- — Z (S) $9282
1910.178 A04
- Issued
- Dec 23, 2019
- Abate by
- Mar 2, 2020
- Penalty
- Initial $9,282 · Current $7,425 Reduced
General-duty citation text
29 CFR 1910.178(a)(4): Modifications and additions which affect capacity and safe operation of powered industrial truck were performed by the employer without the manufacturer's prior written approval: a) On or about July 4, 2019, and at times prior thereto, employees were exposed to struck-by hazards while operating a Nissan 50 with an Abaco Hydraulic Jib Boom AFJ-25 attachment without the manufacturer's written approval. b) On or about July 4, 2019, and at times prior thereto, employees were exposed to struck-by hazards while operating a Nissan 30 with an Abaco Hydraulic Jib Boom AFJ-25 attachment without the manufacturer's written approval.
Recent events (2)
- — I (S) $7425
- — Z (S) $9282
1910.178 A05
- Issued
- Dec 23, 2019
- Abate by
- Mar 2, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(a)(5): The powered industrial truck was equipped with front-end attachments other than factory installed attachments, however, the employer did not request that the truck be marked to identify the attachments and show the approximate weight of the truck and attachment combination at maximum elevation with load laterally centered: a) On or about July 4, 2019, and at times prior thereto, employees were exposed to struck-by hazards while operating a Nissan 50 with an Abaco Hydraulic Jib Boom AFJ-25 attachment that was not marked to identify the adjusted load capacity. b) On or about July 4, 2019, and at times prior thereto, employees were exposed to struck-by hazards while operating a Nissan 30 with an Abaco Hydraulic Jib Boom AFJ-25 attachment that was not marked to identify the adjusted load capacity.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.178 L01 I
- Issued
- Dec 23, 2019
- Abate by
- Jan 27, 2020
- Penalty
- Initial $9,282 · Current $7,425 Reduced
General-duty citation text
29 CFR 1910.178(l)(1)(i): The employer did not ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l). On or about July 4, 2019, employees were exposed to ejection and struck-by hazards while operating forklifts such as, but not limited to, a Nissan 50 and Nissan a 30 without being properly trained in their operation.
Recent events (2)
- — I (S) $7425
- — Z (S) $9282
1910.178 L06
- Issued
- Dec 23, 2019
- Abate by
- Jan 16, 2020
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.178(l)(6): The employer did not certify that each operator has been trained and evaluated in the operation of powered industrial vehicles as required by this paragraph: On or about July 4, 2019, employees were exposed to ejection and struck-by hazards while operating forklifts such as, but not limited to, a Nissan 50 and Nissan 30 without being certified on their training and evaluation.
Recent events (2)
- — I (S) $0
- — Z (S) $0
More inspections at C & C Sage, INC.
View C & C Sage, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 327991)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 344131925.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.