OSHA Inspection: NEVADA ARMY NATIONAL GUARD

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.37(a)(1): Exit routes shall not have flammable, explosive, combustible gases or flammable furnishings stored in the exit route:    (a) On or about July 25, 2019 and at times prior to that date, for the employees exposed to fire related hazards where three flammable compressed gas cylinders to include but not limited to acetylene were stored adjacent to an emergence exit in the welding bay located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.159(c)(10): The minimum vertical clearance of 18 inches between automatic sprinkler systems sprinklers and the material below was not maintained:  (a) On or about July 25, 2019 and at times prior to that date, for the employees exposed to fire hazards where boxes and  shop material were stored on the top shelf of a storage rack system within three vertical inches of sprinkler heads throughout the electronics  room located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.176(b): Storage of material(s) were not stable and secured against collapse:  (a) On or about July 25, 2019 and at times prior to that date, for the employees exposed struck-by hazards where stored materials to include but not limited to approximately 1,200 lbs. of Oil-Dri absorbent was stored on a rack system not secured against collapse in the back maintenance shop room located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(1): Circular handfed ripsaw(s) were not guarded by an automatically adjusting hood which completely enclosed that portion of the saw above the table and above the material being cut:  (a) On or about July 10, 2019 and at times prior to that date, for the employees exposed to amputation hazards while operating a Powermatic, Model 1880791K, Serial No. 05080880873 table saw to cut wood for a department projects in the wood shop located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(2): Hand-fed circular ripsaw(s) were not furnished with a spreader to prevent material from squeezing the saw or being thrown back on the operator:    (a) On or about July 10, 2019 and at times prior to that date, for the employees exposed to struck-by hazards while operating a Powermatic, Model 1880791K, Serial No. 05080880873 table saw to cut wood for a department projects in the wood shop located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.213(c)(3): Hand-fed ripsaw(s) did not have non kickback fingers or dogs designed to provide adequate holding power for all thicknesses of materials being cut:               (a) On or about July 10, 2019 and at times prior to that date, for the employees exposed to struck-by hazards while operating a Powermatic, Model 1880791K, Serial No. 05080880873 table saw to cut wood for a department projects in the wood shop located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1960.8(a): The Agency head did not furnish employment and a place of employment to each employee that were free from recognized hazards that caused or were likely to cause death or serious physical harm:    (a) On or about July 5, 2019 and at times prior to that data, for the employees exposed to struck-by hazards while operating a HAAS CNC machine, model no. ST-20, serial no. 3100240 where the interlock door safety devise was disabled in the machine shop located at 2444 Fairview Drive, Carson City, Nevada.    (b) On or about July 5, 2019 and at times prior to that data, for the employees exposed to struck-by hazards while operating a HAAS CNC machine, model no. TM-1P, serial no. 1116496 where the interlock door safety devise was disabled in the machine shop located at 2444 Fairview Drive, Carson City, Nevada.     Among other methods, one feasible and acceptable abatement method to correct the hazard would be to install a functioning door interlock device on the HAAS CNC machine in accordance with ANSI B11.22 Safety Requirements for Turning Centers Automatic Numerically Controlled Turning Machines, paragraphs 6.21 Safeguarding and 6.21.2 Automatic Mode that states:    1. Paragraph 6.21: Machine shall be safeguarded whenever practical by fixed or interlocked movable guards.    2. Paragraph 6.21.1.2: Machine operation shall only be possible when the guards are closed and the safeguarding (protective) devices are active. If it is possible, in this mode, to open an interlocked moveable guard, the hazardous movement shall cease and be inhibited.    If opening of the interlocked movable guard gives access to hazards, guard locking shall be provided.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:    (a) On or about July 5, 2019 and at times prior to that date, for the employees exposed to amputation and/or caught-in hazards from rotating machine parts while operating the Bridgeport vertical mill, Serial No. 2J150481 in the machine shop located at 2460 Fairview Drive, Carson City, Nevada.    (b) On or about July 5, 2019 and at times prior to that date, for the employees exposed to amputation and/or caught-in hazards from rotating machine parts while operating the South Bend lathe, Model No. SB1039, Serial No. 0034 in the machine shop located at 2460 Fairview Drive, Carson City, Nevada.    (c) On or about July 5, 2019 and at times prior to that date, for the employees exposed to amputation and/or caught-in hazards from rotating machine parts while operating the Wilton 20 Drill Press, Serial No. 4100021 in the welding shop located at 2460 Fairview Drive, Carson City, Nevada.  Note:  This company was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard which was contained in OSHA Inspection Number 1144109, Citation 1, Item 1, and was affirmed as a final order on August 3, 2016, with respect to a workplace located at 6510 & 6520 Range Road, Las Vegas, NV 89165.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.212(a)(3)(ii): The point of operation of machines whose operation exposed an employee to injury, was not guarded:    (a) On or about July 5, 2019 and at times prior to that date, for the employees exposed to amputation hazards from bladed machine parts while operating the Uni-Hydro Ironworker, Model No. 42-14, Serial No. 3P983 in the welding shop located at 2444 Fairview Drive, Carson City, Nevada.               Note:  This company was previously cited for a violation of this Occupational Safety and Health standard or its equivalent standard which was contained in OSHA Inspection Number 1144109, Citation 1, Item 1, and was affirmed as a final order on August 3, 2016, with respect to a workplace located at 6510 & 6520 Range Road, Las Vegas, NV 89165.

Issued

Oct 1, 2019

Abate by

Nov 4, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.147(c)(7)(i): The employer did not provide adequate training to ensure that the purpose and function of the energy control program was understood by employees:  (a) On or about July 25, 2019 and at times prior to that data, for the employees potentially exposed to physical hazards while performing servicing and maintenance to include but not limited to blade, die and bit changes to equipment throughout the facility located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Oct 28, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.178(q)(7): Industrial trucks were not examined before being placed in service:  (a) On or about July 25, 2019 and at times prior to that date, for the employees who operate the Toyota forklift truck, model 8FDU25, serial no. 32309 located at 2444 Fairview Drive, Carson City, Nevada.

Issued

Oct 1, 2019

Abate by

Nov 4, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.179(j)(3): A complete periodic inspection of crane(s) had not been conducted in the past 12 months:  (a) On or about July 24, 2019 and at times prior to that data, for the employees potentially exposed to physical hazards while operating a two ton crane, model no. 622, serial no. 2677UB-R in the paint preparation bay located at 2444 Fairview Drive, Carson City, Nevada.