OSHA Inspection: DELTA ARSENAL, LLC

Issued

Nov 8, 2019

Abate by

Nov 21, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms, service rooms, and walking-working surfaces were not kept in a clean, orderly, and sanitary condition:    WORKSHOP:  The air hose travelling from the wall to the floor behind the Acra turn 1340 lathe was creating a tripping hazard for the employees.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.132(d)(2): The employer did not verify, through a written certification, the identity of the workplace evaluated, the person certifying that the evaluation had been performed, and the date the hazard assessment was done:    WORKSHOP: The employer had not verified through a written certification that the Workplace Hazard Assessment for personal protective equipment (PPE) had been performed as complete.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.132(f)(1): The employer did not provide training to each employee who was required by this section to use personal protective equipment:  WORKSHOP: The employer had not provided training and information to each employee required to wear personal protective equipment (PPE) on the Workplace Hazard Assessment for PPE.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks:     WORKSHOP:          1. The rotating chuck of the Acur turn 1340 lathe was unguarded.        2.  The ingoing nip point, created by the lower belt and pulley of the Wilton vertical belt sander was unguarded.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.215(b)(9): Guard for abrasive wheel machine where the operator stands in front of the machine was not constructed so that the peripheral protecting member could be adjusted to the constantly decreasing diameter of the wheel:    WORKSHOP:  The AB abrasive grinder was not equipped with tongue guards on both wheels.

Issued

Nov 8, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.304(f)(1)(iv): Overcurrent devices for circuits rated 600 volts, nominal, or less, were not readily accessible to each employee or authorized building management personnel:    WORKSHOP/BREAK AREA: The 208-volt electrical panel having built-in overcurrent protection devices was blocked by two (2) boxes containing bull eye camera system, sticker tape, and rack roller.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $2,501 · Current $1,740 Reduced

General-duty citation text

29 CFR 1910.305(b)(2): Each outlet box in completed installations did not have a cover, faceplate, or fixture canopy:    WORKSHOP/HALLWAY:  The outlet box used for the compressor was not equipped with a cover or faceplate.

Issued

Nov 8, 2019

Abate by

Dec 30, 2019

Penalty

Initial $3,334 · Current $2,210 Reduced

General-duty citation text

29 CFR 1910.305(g)(1)(i): Flexible cords and cables were not approved for conditions of use and location:    WORKSHOP/BREAK AREA: The black flexible power cords of the coffee pots, the microwave oven, and the refrigerator were attached to the window frames.

Issued

Nov 8, 2019

Penalty

Initial $0 · Current $0

General-duty citation text

29 CFR 1910.101(b): The in-plant handling, storage, and utilization of all compressed gases in cylinders, portable tanks, rail tankcars, or motor vehicle cargo tanks were not in accordance with Compressed Gas Association Pamphlet P-1-1965, which is incorporated by reference as specified in CFR 1910.6:  WORKSHOP/BREAK AREA: The employer had not secured the two (2) carbon dioxide gas cylinders in the break area.