BENBROOK, TX —
OSHA Inspection: DAVID HORTON
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of DAVID HORTON in 8125 SPANISH HILLS DRIVE, BENBROOK, TX 76126 (NAICS 238130). OSHA activity number 346270093.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- DAVID HORTON
- Site address
- 8125 SPANISH HILLS DRIVE
- City
- BENBROOK
- State
- TX
- ZIP
- 76126
- Mailing
- 7563 BLANCHARD WAY, FORT WORTH, TX 76126
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 5
- Ownership type
- A
Citations
5 citations on file for this inspection.
1926.102 A01
- Issued
- Nov 1, 2022
- Abate by
- Nov 9, 2022
- Penalty
- Initial $2,486 · Current $500 Reduced
General-duty citation text
29 CFR 1926.102(a)(1): Eye and face protective equipment were not used when machines or operations presented potential eye or face injury from physical, chemical, or radiation agents. At the jobsite, employees operating Interchange Metabo nail guns while performing framing activities were not wearing eye protection, exposing employees to the hazard of being struck by flying objects.
Recent events (3)
- — F (O) $500
- — C (S) $2486
- — Z (S) $2486
1926.403 B01 I
- Issued
- Nov 1, 2022
- Abate by
- Nov 9, 2022
- Penalty
- Initial $3,729 · Current $1,000 Reduced
General-duty citation text
29 CFR 1926.403(b)(1)(i): Safety of equipment was not determined on the basis of suitability of the equipment for an identified purpose as evidenced by listing, labeling, or certification for that identified purpose. At the construction site, the eight electrical receptacle box that was not approved by listing and labeling and manufacture design, with the design and method made and used by the employer, to energize hand held power equipment exposing employees to the hazard of electrical shock.
Recent events (3)
- — F (O) $1000
- — C (S) $3729
- — Z (S) $3729
1926.405 G02 III
- Issued
- Nov 1, 2022
- Abate by
- Nov 9, 2022
- Penalty
- Initial $2,486 · Current $0 Reduced
General-duty citation text
29 CFR 1926.405(g)(2)(iii): Splices. Flexible cords shall be used only in continuous lengths without splice or tap. At the jobsite, employees used a black extension cord spliced to a gray power cord and wrapped with black tape, supplying power to a DeWalt Skill saw, exposing employees to the hazard of electrical burns and shock.
Recent events (3)
- — F (O) $0
- — C (S) $2486
- — Z (S) $2486
1926.501 B13
- Issued
- Nov 1, 2022
- Abate by
- Nov 9, 2022
- Penalty
- Initial $4,351 · Current $1,500 Reduced
General-duty citation text
29 CFR 1926.501(b)(13): Each employee(s) engaged in residential construction activities 6 feet (1.8 m) or more above lower levels were not protected by guardrail systems, safety net system, or personal fall arrest system. At the jobsite, employees engaged in framing activities at a height of over 6 feet were not protected by a fall arrest system. Employees were exposed to an unprotected fall of over 10 feet to the ground below.
Recent events (3)
- — F (O) $1500
- — C (S) $4351
- — Z (S) $4351
1926.503 A01
- Issued
- Nov 1, 2022
- Abate by
- Nov 9, 2022
- Penalty
- Initial $349 · Current $0 Reduced
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards: At the jobsite, the employer did not provide a training program with hazard recognition and avoidance training where employees were performing framing activities above 6 feet without fall protection and exposed to fall hazards at a heights of approximately 10 feet to the ground below.
Recent events (3)
- — F (O) $0
- — C (O) $349
- — Z (O) $349
More inspections at David Horton
View David Horton's full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346270093.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.