SAN ANTONIO, TX —
OSHA Inspection: G4 GEOMATIC RESOURCES
Complaint inspection · Safety discipline
At a glance
On , OSHA opened a complaint safety inspection of G4 GEOMATIC RESOURCES in 1019 E NAKOMA DR, SAN ANTONIO, TX 78216 (NAICS 423430). OSHA activity number 346435563.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- G4 GEOMATIC RESOURCES
- Site address
- 1019 E NAKOMA DR
- City
- SAN ANTONIO
- State
- TX
- ZIP
- 78216
- Mailing
- 1019 E NAKOMA DR, SAN ANTONIO, TX 78216
What kind of inspection was it?
- Inspection type
- Complaint (B)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 423430
- Employees
- 40
- Ownership type
- A
Citations
7 citations on file for this inspection.
1910.28 B01 I
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $6,250 · Current $4,000 Reduced
General-duty citation text
29 CFR 1910.28(b)(1)(i): The employer did not ensure that each employee on a walking-working surface with an unprotected side or edge that is 4 feet (1.2 m) or more above a lower level is protected from falling by one or more of the following: guardrail system, safety net system, or personal fall protection system: a) Storage mezzanine, entrance and walkway: On or about January 12, 2023, and at times prior thereto, employees were exposed to a fall hazard of greater than 4 feet, while accessing the mezzanine without a guardrail system in place. b) Storage mezzanine, northside: On or about January 12, 2023, and at times prior thereto, employees were exposed to a fall hazard of greater than 4 feet, while storing equipment and supplies on a mezzanine without a guardrail system in place.
Recent events (2)
- — I (S) $4000
- — Z (S) $6250
1910.28 B11 II
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.28(b)(11)(ii):29 CFR 1910.28(b)(11)(ii): The employer did not ensure that each flight of stairs having at least 3 treads and at least 4 risers is equipped with stair rail systems and handrails as described in 29 CFR 1910.28 Table D-2-Stairway Handrail Requirements: Storage mezzanine: On or about January 12, 2023, and at times prior thereto, employees were exposed to a fall hazard of greater than 4 feet, while storing equipment and supplies on a mezzanine without handrails.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.213 G03
- Issued
- May 16, 2023
- Penalty
- Initial $6,250 · Current $0 Reduced
General-duty citation text
29 CFR 1910.213(g)(3): Swing cutoff saw(s) were not provided with limit chains or other equally effective devices to prevent the saw from swinging beyond the front edges of the table: Near the entrance of the shop: On or about January 12, 2023, and at times prior thereto, employees were exposed to an amputation hazard while operating a 12 inch Swing Saw with the saw blade that extended beyond the table.
Recent events (2)
- — I (S) $0
- — Z (S) $6250
1910.219 B01
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $9,376 · Current $6,500 Reduced
General-duty citation text
29 CFR 1910.219(b)(1): Flywheel(s) with parts seven feet or less above floor(s) or platform(s) were not guarded in accordance with the requirements specified in 29 CFR 1910.219(b)(1)(i) through (b)(1)(iv)(a): a) Shop entrance on left, swing saw 007: On or about January 12, 2023, and at times prior thereto, employees were exposed to struck-by hazards of rotating parts from an unguarded flywheel. b) Shop right rear, swing saw 009: On or about January 12, 2023, and at times prior thereto, employees were exposed to struck-by hazards of rotating parts from an unguarded flywheel. c) Shop entrance on left, lath saw 001: On or about January 12, 2023, and at times prior thereto, employees were exposed to struck-by hazards of rotating parts from an unguarded flywheel.
Recent events (2)
- — I (S) $6500
- — Z (S) $9376
1910.305 B01 II
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $6,250 · Current $4,500 Reduced
General-duty citation text
29 CFR 1910.305(b)(1)(ii): Unused openings in boxes, cabinets, or fittings were not effectively closed: Shop entrance next to fire extinguisher: On or about January 12,2023, and at time thereto, employees were exposed to electrical shock hazards due to unused openings in a 240v electrical box that was not effectively closed.
Recent events (2)
- — I (S) $4500
- — Z (S) $6250
1910.305 G01 IV
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $9,376 · Current $0 Reduced
General-duty citation text
29 CFR 1910.305(g)(1)(iv): Flexible cords and/ or cables were used for purposes prohibited by paragraphs (A) through (F) of 29 CFR 1910.305(g)(1)(iv)(a): In the shop area: On or about January 12, 2023, and at times prior thereto, employees were exposed to electrical hazards from an electrical extension cord that was fastened by staples.
Recent events (2)
- — I (S) $0
- — Z (S) $9376
1904.40 A
- Issued
- May 16, 2023
- Abate by
- Jun 12, 2023
- Penalty
- Initial $1,562 · Current $800 Reduced
General-duty citation text
29 CFR 1904.40(a):The employer did not provide an authorized government representative the records within the four business hours: At this establishment: On January 12, 2023 the employer failed to provide records of the injury and illness records to an authorized representative.
Recent events (2)
- — I (O) $800
- — Z (O) $1562
More inspections at G4 Geomatic Resources
View G4 Geomatic Resources's full OSHA safety record →
More inspections in this industry (NAICS 423430)
More inspections in TX
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 346435563.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.