HAZLEHURST, MS —
OSHA Inspection: FAB-TEK OF CENTRAL MISSISSIPPI, INC.
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of FAB-TEK OF CENTRAL MISSISSIPPI, INC. in 19171 U.S. 51, HAZLEHURST, MS 39083 (NAICS 332999). OSHA activity number 347364986.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- FAB-TEK OF CENTRAL MISSISSIPPI, INC.
- Site address
- 19171 U.S. 51
- City
- HAZLEHURST
- State
- MS
- ZIP
- 39083
- Mailing
- P.O. BOX 127, GALLMAN, MS 39077
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Complete (A)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Case closed
- Last modified
- Data loaded
Establishment context
- NAICS code
- 332999
- Employees
- 40
- Ownership type
- A
Citations
6 citations on file for this inspection.
1910.147 C04 I
- Issued
- May 13, 2024
- Abate by
- Jun 27, 2024
- Penalty
- Initial $6,453 · Current $3,549 Reduced
General-duty citation text
29 CFR 1910.147(c)(4)(i): Procedures were not developed, documented and utilized for the control of potentially hazardous energy when employees were engaged in activities covered by this section: (a) Facility - On or about March 27, 2024, the employer did not develop specific lockout tagout procedures for equipment with multiple energy sources such as PA Riot air jet, press brakes, etc., exposing employees to amputation hazards.
Recent events (2)
- — I (S) $3549.15
- — Z (S) $6453
1910.212 A01
- Issued
- May 13, 2024
- Abate by
- Jun 5, 2024
- Penalty
- Initial $4,839 · Current $2,661 Reduced
General-duty citation text
29 CFR 1910.212(a)(1): One or more methods of machine guarding was not provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks: (a) Cut Shop - On or about March 27,2024, the employer did not guard the rotating chuck on a Sharp Lathe 1880LV exposing the employees to amputation hazards.
Recent events (2)
- — I (S) $2661.45
- — Z (S) $4839
1910.217 B04 I
- Issued
- May 13, 2024
- Abate by
- Jun 5, 2024
- Penalty
- Initial $4,839 · Current $2,661 Reduced
General-duty citation text
29 CFR 1910.217(b)(4)(i): The pedal mechanism shall be protected to prevent unintended operation from falling or moving objects or by accidental stepping onto the pedal. (a)-On or about March 27, 2024, the pedal mechanism on the Standard Industrial Press Brake AB250-12 was not completely guarded exposing the employees to an amputation hazard.
Recent events (2)
- — I (S) $2661.45
- — Z (S) $4839
1910.217 C02 I A
- Issued
- May 13, 2024
- Abate by
- Jun 5, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1910.217(c)(2)(i)(a): Point of operation guard(s) on mechanical power press(es) did not prevent entry of hands or fingers into the point of operation by reaching through, over, under or around the guard(s): (a) Welding area- On or around March 27, 2024, the Standard Industrial Press Brake AB250-12 was not guarded on the sides, exposing the employees to amputation hazards.
Recent events (2)
- — I (S) $0
- — Z (S) $0
1910.242 B
- Issued
- May 13, 2024
- Penalty
- Initial $4,839 · Current $2,661 Reduced
General-duty citation text
29 CFR 1910.242(b): Compressed air used for cleaning. Compressed air shall not be used for cleaning purposes except where reduced to less than 30 p.s.i. and then only with effective chip guarding and personal protective equipment: (a)Cut Shop - On or about March 27, 2024, air pressure used to dry and clean material cut from the PA Riot Air jet was 60 p.s.i. exposing employees to eye injuries.
Recent events (2)
- — I (S) $2661.45
- — Z (S) $4839
1910.305 B01 II
- Issued
- May 13, 2024
- Abate by
- Jun 5, 2024
- Penalty
- Initial $4,839 · Current $2,661 Reduced
General-duty citation text
29 CFR 1910.305(b)(1)(ii): Unused openings in boxes, cabinets, or fittings were not effectively closed: (a) Copper shop- On or about March 27,2024 the panel box was missing blanks for the circuit breakers operating the copper shop exposing employees to an electrical hazard.
Recent events (2)
- — I (S) $2661.45
- — Z (S) $4839
More inspections at Fab-Tek of Central Mississippi, INC.
View Fab-Tek of Central Mississippi, INC.'s full OSHA safety record →
More inspections in this industry (NAICS 332999)
More inspections in MS
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347364986.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.