SOUTH HOLLAND, IL —
OSHA Inspection: MARIO MENDEZ
Planned inspection · Safety discipline
At a glance
On , OSHA opened a planned safety inspection of MARIO MENDEZ in 610 TOLLVIEW DR., SOUTH HOLLAND, IL 60473 (NAICS 238130). OSHA activity number 347503757.
OSHA opens inspections for many reasons — routine scheduling under a national or local emphasis program, an employee complaint or referral, or a follow-up after a reported injury. Opening or conducting an inspection is not itself an allegation or a finding that this employer broke any rule; any findings appear as the citations listed below, and citations can be contested, reduced, or withdrawn.
Where did this inspection happen?
- Establishment
- MARIO MENDEZ
- Site address
- 610 TOLLVIEW DR.
- City
- SOUTH HOLLAND
- State
- IL
- ZIP
- 60473
- Mailing
- 1204 W. COUNTY LINE RD., BEECHER, IL 60401
What kind of inspection was it?
- Inspection type
- Planned (H)
- Scope
- Partial (B)
- Discipline
- Safety
- Advance notice
- No
- Union status
- B
When did the case open and close?
- Opened
- Closing conference
- Last modified
- Data loaded
Establishment context
- NAICS code
- 238130
- Employees
- 3
- Ownership type
- A
Citations
5 citations on file for this inspection.
1903.19 C01
- Issued
- Dec 4, 2024
- Abate by
- Jan 8, 2025
- Penalty
- Initial $388 · Current $388
General-duty citation text
29 CFR 1903.19(c)(1): Within 10 calendar days after the abatement date, the employer must certify to OSHA (the Agency) that each cited violation has been abated, except as provided in paragraph (c)(2) of this section. a. On or about December 4, 2024, - the employer did not certify to OSHA within 10 days after the abatement date that each of the following cited violations issued had been corrected: Citation Number Item Number Abatement Date 01002b11/01/2024
Recent events (1)
- — Z (O) $388
1926.102 A01
- Issued
- Sep 27, 2024
- Penalty
- Initial $3,457 · Current $3,457
General-duty citation text
29 CFR 1926.102(a)(1): The employer did not ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation. a. On or about May 23, 2024, at the above addressed jobsite, an employee using a pneumatic nail gun was not wearing safety glasses, thereby exposing the employee to hazards associated with eye injuries.
Recent events (1)
- — Z (S) $3457
1926.501 B01
- Issued
- Sep 27, 2024
- Penalty
- Initial $4,839 · Current $4,839
General-duty citation text
29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was 6 feet (1.8 m) or more above a lower level was not protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems. a. On or about May 23, 2024, at the above addressed jobsite, employees performing commercial carpentry framing operations, approximately twenty (20) feet above a lower level, were not protected from falls, thereby exposing the employees to fall hazards.
Recent events (1)
- — Z (S) $4839
1926.503 A01
- Issued
- Sep 27, 2024
- Abate by
- Nov 1, 2024
- Penalty
- Initial $0 · Current $0
General-duty citation text
29 CFR 1926.503(a)(1): The employer did not provide a training program for each employee potentially exposed to fall hazards to enable each employee to recognize the hazards of falling and the procedures to be followed in order to minimize these hazards: a. On or about May 23, 2024, at the above addressed jobsite, employees performing commercial carpentry framing operations had not been provided with adequate fall protection training, thereby exposing the employees to fall hazards.
Recent events (1)
- — Z (S) $0
1926.1053 B04
- Issued
- Sep 27, 2024
- Penalty
- Initial $4,148 · Current $4,148
General-duty citation text
29 CFR 1926.1053(b)(4): Ladder(s) were used for purposes other than the purpose for which they were designed: a. On or about May 23, 2024, at the above addressed jobsite, the ladder used to access and egress the working surface was a ten-foot A-Frame ladder that was closed and leaned against the structure, thereby exposing the employees to fall hazards.
Recent events (1)
- — Z (S) $4148
More inspections at Mario Mendez
View Mario Mendez's full OSHA safety record →
More inspections in this industry (NAICS 238130)
More inspections in IL
Source
This record is reproduced from the U.S. Department of Labor Open Data API (OSHA inspection dataset). The original IMIS detail view is available at OSHA's Establishment Search for activity number 347503757.
Look up any company's OSHA accident reports by company, or browse severe injury reports by year, state, and company.